Sony HVR-S270J Service Manual page 244

1-2-2. Initialization of 8, 9, C, 13, 18, 1C, 1D, 1E
Page Data
1. Initializing of 8, 9, C, 13, 18, 1C, 1D, 1E Page Data
Note 1: If "Initialization of Pages 8, 9, C, 13, 18, 1C, 1D, 1E" is
executed, all data on pages 8, 9, C, 13, 18, 1C, 1D, 1E
are initialized. (Only an individual page cannot be ini-
tialized)
Note 2: If the 8, 9, C, 13, 18, 1C, 1D, 1E page data has been
initialized, the following adjustments need to be per-
formed again.
1) Modification of 8, 9, C, 13, 18, 1C, 1D, 1E page data
2) Electronic viewfinder system adjustments (if all ar-
eas were initialized)
3) LCD system adjustments (if all areas were initial-
ized)
4) Node unique ID No. input (if all areas were initial-
ized)
5) Servo, RF system adjustments (if all areas were ini-
tialized)
6) Video system adjustments (if all areas were initial-
ized)
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Initializing method:
Order Page Address Data
1 0 01
2 0 10
3 3 81
4 3 80
5 3 80
6 3 91
7 3 90
HVR-S270J/S270U/S270N/S270E/S270P/S270C
8
00 to FF
9
00 to FF
C
10 to FF
13
00 to FF
18
00 to FF
1C
00 to FF
1D
00 to FF
1E
00 to FF
Procedure
01
00
Set the following data, and
press PAUSE (Write) button.
(Note 3)
00: Initializing all areas
01: Initializing other than
adjustment address
0C Press PAUSE (Write) button.
Check the data changes to
"1C".
Set the following data, and
press PAUSE (Write) button.
(Note 3)
01: Initializing all areas
11: Initializing other than
adjustment address
0C Press PAUSE (Write) button.
Order Page Address Data
8 3 90
9
Note 3: If other than adjustment address was initialized, the ad-
justed data is not initialized.
2. Modification of 8, 9, C, 13, 18, 1C, 1D, 1E Page Data
If the 8, 9, C, 13, 18, 1C, 1D, 1E page data has been initialized,
change the data of the "Fixed data-2" address shown in the fol-
lowing table by manual input.
Processing before Modification 8, 9, C, 13, 18, 1C, 1D, 1E
page data:
Order Page Address Data
1 0 01
2 0 10
3 3 71
Modifying Method:
1) If modification of data on pages 8, 9, C, set data: 00 to page: 0,
address: 10, and then select pages 8, 9, C.
2) If modification of data on pages 13, 18, 1C, 1D, 1E, set data:
01 to page: 0, address: 10, and then select pages 3, 8, C, D, E.
After the modification of data finished, return the data on page:
0, address: 10 to "00".
3) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the cam-
corder may not operate.
4) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
5) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table.
If different, change them to the adjustment initial values.
Processing after Completing Modification 8, 9, C, 13, 18, 1C,
1D, 1E page data:
Order Page Address Data
1 0 01
2 0 10
3 3 70
4 3 70
5 2 00
6 2 01
6-10
Procedure
Check the data changes to
"1C".
Perform "Modification of 8,
9, C, 13, 18, 1C, 1D, 1E Page
Data"
Procedure
01
00
01 Press PAUSE (Write) button.
Procedure
01
00
10 Press PAUSE (Write) button.
Check the data changes to
"11".
29
29 Press PAUSE (Write) button.