Advertisement
Advertisement
Table of Contents
Related Manuals for JOYTECH PY500AC
Summary of Contents for JOYTECH PY500AC
- Page 1 Sliding Gate Operator User's Manual PY5 5 5 5 00 00A A A A C C C C...
-
Page 2: Table Of Contents
PY500AC SLIDING GATE OPERATOR OUTLINE 1. Products introduction ……………………………………2 2. Important safety precautions ……………………………2 ……………………………2 3. Main technical parameters 4. Mechanical Installation …………………………………2 ………………………………………………5 5. Adjustment 6. Wire Connecting …………………………………………6 7. Turning and operation ……………………………………8 8. Programming Process ……………………………………10 ……………………………………………11 9. -
Page 3: Products Introduction
Installation Installation The PY500AC will handle gate weighting up to 500kg and up to 12m if the proper installation procedures have been followed. The PY500AC gate operator operates by forcing a drive rack by a drive gear. The entire configuration is... - Page 4 Gate operator Fig.1 Gate preparation Be sure the gate is properly installed and slides smoothly before installing the PY500AC sliding gate operator. The gate must be plumb, level, and move freely. Conduit In order to protect the cable, use PVC conduit for low voltage power cable and control wires. Conduit must be preset into the concrete when it is poured.
- Page 5 PY500AC SLIDING GATE OPERATOR Gate operator Gear Spring washer Plain washer Groundsill Input power Fig.2 Operator base (see Fig.3) After the concrete has hardened, mount the gate operator base to the concrete pad. Verify that the base is properly leveled.
-
Page 6: Adjustment
PY500AC SLIDING GATE OPERATOR � When the rack has been installed, to ensure it meshes correctly with the gear. � The space between rack and gear is about 0.5mm. Fig.4 Fig.4 Fig.4 Fig.4 5. 5. 5. 5. Adjustment Adjustment Adjustment... -
Page 7: Wire Connecting
PY500AC SLIDING GATE OPERATOR M6X10 Fig.6 Manual operation In case of power failure use key unlock the lock and pull down the release bar about 90 degree to open or close gate manually, use the release key as follow: �... - Page 8 PY500AC SLIDING GATE OPERATOR Fig.8 Wiring Wiring notes notes notes of of of of control control control board board Wiring Wiring notes control board board a. Power Input(X1):E (Earth),L (Live),N (Neutral). PY500AC: AC220V PY500ACU:AC110V b. Caution light: connect caution light wire toD1 and D2(terminal X3)
-
Page 9: Turning And Operation
Schematic diagram d. Three-button switch / single-button switch (keypad): The PY500AC is equipped with interfaces for three-button switch and single-button switch (keypad). To install the keypad attach one lead of your keypad to ‘CLS’ of terminal X4 and the other to the ‘COM’. - Page 10 PY500AC SLIDING GATE OPERATOR buttons or three buttons together, but you need repeat the program/learn process if you want to use more than one button. Button 1 Button 2 Button 3 Button 4 Fig.12 Remote transmitter � Adding extra remote controls (Learn): Remove the cover, press the learn button ‘AN1’ (Fig.8), then the ‘LED2’...
-
Page 11: Programming Process
PY500AC SLIDING GATE OPERATOR 8. 8. 8. 8. Porgramming Porgramming Porgramming Porgramming Process Process Process Process Table of the DIP-switch Position DIP-switch Function SET Three-button switch Single-button switch(the CLS and COM), OPN and COM is “open door” function also. When the 2 and 3 all ON, the Controller haven’t Auto-close function. -
Page 12: Maintenance
PY500AC SLIDING GATE OPERATOR positions or during opening. � Open Open Open Open priority: priority: priority: priority: The gate will return to open if press ‘OPEN’ button of external button switch during closing. � � � � Limit Limit Limit... - Page 13 PY500AC SLIDING GATE OPERATOR Item Quantity PY500AC sliding gate operator Transmitter Release key User’s manual...
Need help?
Do you have a question about the PY500AC and is the answer not in the manual?
Questions and answers