Subscribe to Our Youtube Channel
Related Manuals for JOYTECH PY800AC
Summary of Contents for JOYTECH PY800AC
- Page 1 Sliding Gate Operator User's Manual PY800AC/PY1400AC PY800AC/PY1400AC PY800AC/PY1400AC PY800AC/PY1400AC...
- Page 2 PY800AC/PY1400AC SLIDING GATE OPERATOR 1. 1. 1. 1. Products Products introduction Products Products introduction introduction introduction please please read read instructions instructions carefully carefully before before proceeding. proceeding. please please read read the the instructions instructions carefully carefully before before proceeding.
- Page 3 Installation Installation Mechanical Installation Installation The PY800AC/PY1400AC will handle gate weighting up to 800kg/1400 kg and up to 14m/20m if the proper installation procedures have been followed. The PY800AC/PY1400AC gate operator operates by forcing a drive rack by a drive gear.
-
Page 4: Gate Operator
PY800AC/PY1400AC SLIDING GATE OPERATOR In order to protect the cable, use PVC conduit for low voltage power cable and control wires. Conduit must be preset into the concrete when it is poured. Wires within the conduit shall be located or protected so that no damage can result from contact with any rough or sharp part. - Page 5 PY800AC/PY1400AC SLIDING GATE OPERATOR Using bolts and washers mount the gate operator to the base and insert the cover. Check the operator and make sure it is lined up with the gate. Fig.3 Installation Installation of of of of Rack...
- Page 6 PY800AC/PY1400AC SLIDING GATE OPERATOR Fig.4 Fig.4 Fig.4 Fig.4 5. 5. 5. 5. Adjustment Adjustment Adjustment Adjustment Spring limit switch � To ensure safety, it is recommended to install limit switches at both ends of the gate to prevent the gate from sliding out of the rails. The rails must be installed horizontally.
- Page 7 PY800AC/PY1400AC SLIDING GATE OPERATOR � Release the gear with the key and push the sliding gate manually to pre-determine the position, fix the block to the rack and lock the gear by push up the release bar. Moving the gate electrically, adjust the block to the proper position until the position of the opening and closing meet the requirement.
-
Page 8: Sliding Gate
PY800AC/PY1400AC SLIDING GATE OPERATOR Sliding gate Magnetic Limit block Rack Gear Magnetic limit Fig.5 Spring limit Magnetic limit Fig.6... - Page 9 PY800AC/PY1400AC SLIDING GATE OPERATOR Manual operation In case of power failure use key unlock the lock and pull down the release bar about 90 degree to open or close gate manually, use the release key as follow: � Fit the supplied key in the lock.
- Page 10 PY800AC/PY1400AC SLIDING GATE OPERATOR 6. 6. 6. 6. Wire Wire Wire Connecting Connecting Wire Connecting Connecting Make sure that the power is OFF before making any electrical connections. Remove the cover, perform the wiring (See Fig.8 and wiring notes for control board) and replace the cover again.
-
Page 11: Control Board
Fig.9 infrared infrared infrared Schematic diagram d. Three-button switch / single-button switch (keypad): The PY800AC/ PY1400AC is equipped with interfaces for three-button switch and single-button switch (keypad). To install the keypad attach one lead of your keypad to ‘CLS’ of terminal X4 and the other to the ‘COM’. - Page 12 PY800AC/PY1400AC SLIDING GATE OPERATOR Motor and capacitor (Terminal X2, X3): V (com), U (Positive direction), W (Opposite direction), E (grounding), C (capacitor) Capacitor Motor Control board Terminal X3 Terminal X2 Fig.11 7. 7. 7. 7. Tuning Tuning Tuning operation operation...
- Page 13 PY800AC/PY1400AC SLIDING GATE OPERATOR Button 1 Button 2 Button 3 Button 4 Fig.12 Remote transmitter � Adding extra remote controls (Learn): Remove the cover, press the learn button ‘AN1’ (Fig.8), then the ‘LED2’ (Fig.8) will be on and turn off, then press the remote control button which you want to use, the ‘LED2’...
- Page 14 PY800AC/PY1400AC SLIDING GATE OPERATOR button, the gate stops running. And the ‘LED2’ is turns off. � Verify open direction: If the gate does not move in the desired direction, then you will need to reverse the motor operating direction, open the black plastic cover, you can do this by exchanging wires ‘U’...
- Page 15 PY800AC/PY1400AC SLIDING GATE OPERATOR � � � � Three-button Three-button mode mode external external button button switch switch (not (not supply): supply): supply): press Three-button Three-button mode mode external external button button switch switch (not (not supply): ‘OPEN’ button, the gate opens. Press ‘STOP’ button, the gate stops.
- Page 16 PY800AC/PY1400AC SLIDING GATE OPERATOR � � � � Disconnect from mains supply before replacing bulb. � � � � Be sure to read the entire manual before attempting to perform any installation or service to the door operator. � � � �...
- Page 17 PY800AC/PY1400AC SLIDING GATE OPERATOR Item Quantity PY800AC/PY1400AC sliding gate operator Transmitter Release key User’s manual...
- Page 18 PY800AC/PY1400AC SLIDING GATE OPERATOR OUTLINE OUTLINE OUTLINE OUTLINE 1. Products introduction ………………………………………………1 2. Important safety precautions ………………………………………1 3. Main technical parameters ……………………………………… 1 4. Mechanical Installation …………………………………………… 2 5. Adjustment ………………………………………………………… 5 6. Wire Connecting …………………………………………………… 9 7. Turning and operation …………………………………………… 11 8.
Need help?
Do you have a question about the PY800AC and is the answer not in the manual?
Questions and answers