Danfoss VLT FC 322 Instruction Manual page 80

Index VLT® Automation VT Drive FC 322 D-Frame Instruction Manual
Power
Connections..................................................................................... 2-5
Factor................................................................................. 1-3, 2-7, 3-1
Pre-Installation Check List................................................................ 2-1
Programming.................... 1-2, 3-4, 4-2, 5-4, 5-9, 8-5, 3-2, 4-1, 4-3
Protection
Protection....................................................................................... 10-7
And Features.................................................................................. 10-6
Pulse Inputs........................................................................................ 10-3
Q
Quick
Menu.................................................................................. 4-2, 5-1, 4-2
Set-up................................................................................................. 3-3
R
Ramp-down Time............................................................................... 3-4
Ramp-up Time...................................................................................... 3-4
Reference............................................................. 0-1, 7-2, 7-3, 4-2, 5-1
Relay Outputs.......................................................................... 2-13, 10-4
Remote
Commands........................................................................................ 1-2
Programming................................................................................... 5-9
Reference........................................................................................... 7-2
Reset........................................ 4-1, 4-4, 7-3, 8-1, 8-5, 8-11, 10-6, 4-3
Residual Current Devices (RCDs)................................................... 2-5
Restoring Default Settings............................................................... 4-4
RFI Filter............................................................................................... 2-10
RMS Current.......................................................................................... 1-3
RS-485................................................................................................... 2-13
Run
Command......................................................................................... 3-4
Permissive......................................................................................... 7-2
S
Screened Control Cables................................................................ 2-12
Serial Communication...... 1-2, 2-12, 2-13, 4-3, 7-1, 7-2, 7-3, 8-1,
2-13
Set Up...................................................................................................... 4-2
Setpoint.................................................................................................. 7-3
Set-up...................................................................................................... 4-2
Shielded
Cable........................................................................................... 2-4, 3-1
Wire..................................................................................................... 2-4
Short Circuit.......................................................................................... 8-7
Smart Application Set-up (SAS)..................................................... 3-2
Specifications....................................................................................... 1-2
Speed Reference................................................................. 3-4, 5-2, 7-1
MG21E122 - VLT® is a registered Danfoss trademark
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-20776-Danfoss-131X8139-VLT-Automation-VT-Drive-VFD-FC322-230V-20-HP.aspx
Start Up.................................................................................. 1-2, 4-4, 5-1
Status
Messages........................................................................................... 7-1
Mode................................................................................................... 7-1
Stop Command.................................................................................... 7-2
Supply Voltage.................................................... 2-11, 2-13, 8-8, 10-4
Surroundings..................................................................................... 10-5
Switching Frequency......................................................................... 7-2
System Feedback................................................................................ 1-2
T
Temperature Limits............................................................................ 3-1
Terminal
53................................................................................................. 5-1, 5-2
Locations D1h.................................................................................. 2-7
Locations D2h.................................................................................. 2-8
Programming................................................................................ 2-13
Programming Examples............................................................... 5-3
Thermistor
Thermistor..................................................................... 2-11, 8-6, 6-4
Control Wiring............................................................................... 2-11
Torque
Characteristics............................................................................... 10-2
For Terminals................................................................................. 10-8
Limit..................................................................................................... 3-4
Transient Protection.......................................................................... 1-3
Trip Function........................................................................................ 2-4
Troubleshooting................................................................. 1-2, 8-5, 9-1
U
Uploading Data To The LCP............................................................ 4-4
Using Screened Control Cables................................................... 2-11
V
Voltage Imbalance.............................................................................. 8-5
W
Warning And Alarm Definitions..................................................... 8-2
Wire Type And Ratings...................................................................... 2-5
Wiring To Control Terminals......................................................... 2-13
12-3