Related Manuals for Extron electronics XTP FT HD 4K
Summary of Contents for Extron electronics XTP FT HD 4K
- Page 1 User Guide XTP Systems XTP FT HD 4K XTP Fiber Optic Transmitter 68-2201-01 Rev. E 01 19...
- Page 2 Safety Instructions Safety Instructions • English Istruzioni di sicurezza • Italiano AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire This symbol, ,when used on the product, is intended WARNING: l’utente della presenza di tensione non isolata pericolosa all’interno del to alert the user of the presence of uninsulated dangerous voltage within contenitore del prodotto che può...
- Page 3 ついては、 エクス トロンのウェブサイ ト より 『Extron Safety www.extron.com and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください。 Copyright © 2015-2019 Extron Electronics. All rights reserved. www.extron.com Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ( ®...
- Page 4 This interference must be corrected at the expense of the user. Class 1 Laser Product Any service to this product must be carried out by Extron Electronics and its qualified service personnel. CAUTION: Using controls, making adjustments, or performing procedures in a manner other than what is specified herein may result in hazardous radiation exposure.
- Page 5 Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessure mineure. ATTENTION: •...
-
Page 6: Table Of Contents
Tabletop Mounting ........28 HDMI Audio Switch .......... 11 Furniture Mounting........28 EDID ..............11 Rack Mounting ..........28 Audio Output Overview ........11 Firmware Download .......... 29 Reset Modes ............ 12 XTP FT HD 4K Fiber Transmitter • Contents... - Page 7 XTP FT HD 4K Fiber Transmitter • Contents xiii...
-
Page 8: Introduction
700 m (2,297 feet) using a multimode OM4 fiber cable or up to 10 km (6.2 mi) with a singlemode fiber cable. The following diagram shows one way the XTP FT HD 4K can be integrated in an XTP point-to-point application. -
Page 9: System Compatibility
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. Le XTP FT HD 4K émet une lumière invisible en continu qui peut être dangereux pour les yeux, à utiliser avec précaution. -
Page 10: Control Methods
Certain features can also be controlled through an XTP matrix switcher (see the XTP matrix switcher user guide at www.extron.com). NOTE: If the XTP FT HD 4K is connected to an XTP matrix switcher, configure it through the XTP matrix switcher (se the XTP matrix switcher user guide for SIS command or the XTP System Configuration Help File for software details). -
Page 11: Control Features
1" (2.5 cm) high, half rack width metal enclosure — Allows for discreet placement • and concealment. • Highly reliable, energy-efficient external universal power supply included — Provides worldwide power compatibility, with high demonstrated reliability and low power consumption for reduced operating costs. XTP FT HD 4K Fiber Transmitter • Introduction... -
Page 12: Installation
Installation This section contains the installation procedures and operation methods for the XTP FT HD 4K. Topics in this section include: • Rear Panel Connectors Connection Details • Rear Panel Connectors INPUTS OVER XTP XTP OUT POWER AUDIO AUDIO RS-232 1.0 A MAX... -
Page 13: Transmitter Xtp Interconnection
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. Le XTP FT HD 4K émet une lumière invisible en continu qui peut être dangereux pour les yeux, à utiliser avec précaution. -
Page 14: Connection Details
( ATTENTION: • Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP FT HD 4K Fiber Transmitter • Installation... -
Page 15: Rs-232 And Ir Communication
6 for wiring considerations). Smooth Ridges SECTION A–A Power Supply Tie Wrap Output Cord Captive Screw Connector Figure 6. Power Wiring See the notifications on the next page for other considerations. XTP FT HD 4K Fiber Transmitter • Installation... - Page 16 La longueur idéale est de 5 mm (3/16 inch). Do not tin the stripped power supply leads. Tinned wires are not as secure in the TIP: captive screw connectors and could be pulled out. XTP FT HD 4K Fiber Transmitter • Installation...
-
Page 17: Operation
(see the contact numbers on the last page of this guide for the nearest Extron office). This section contains information about the local operation of the XTP FT HD 4K as well as the operational indicators. Topics in this section include the following: •... -
Page 18: Hdmi Audio Switch
SIS commands. EDID The XTP FT HD 4K can record and save EDID in a user memory location on the transmitter. EDID can come from the loop-through display on the transmitter. For EDID management, use the XTP System Configuration Software (see EDID Minder on page 26). -
Page 19: Reset Modes
(<1 second). SIS command default values including real-time Reset on page 17). adjustments. (mode 5) • The front panel Power LED blinks four times in quick succession during the reset. XTP FT HD 4K Fiber Transmitter • Operation... -
Page 20: Sis Configuration And Control
SIS Configuration and Control This section contains SIS communication details and SIS commands and responses when the host device is connected directly to an XTP FT HD 4K. Topics in this section include the following: • Host Device Connection •... -
Page 21: Using The Command And Response Tables For Sis Commands
= Carriage return with no line feed = Pipe (can be used interchangeably with the character). = Space • = Escape key = Can be used interchangeably with the character. XTP FT HD 4K Fiber Transmitter • SIS Configuration and Control... -
Page 22: Command And Response Tables
Command and Response Tables The following commands are for direct connection to the XTP FT HD 4K (see the XTP matrix switcher user guide for commands sent from the matrix switcher to the transmitter). Command ASCII Command ASCII Response Additional Description... -
Page 23: Edid Commands
= Input reports as an HDCP Authorized device (default) = disabled (default) = Test pattern = 720p @ 50 Hz = 720p @# 60 Hz = 1080p @ 60 Hz XTP FT HD 4K Fiber Transmitter • SIS Configuration and Control... -
Page 24: Device Commands
0, 2, 4, 6 = Output HDCP status = sink device detected, but the output signal is not encrypted 1, 3, 5 = sink device detected and the output signal is encrypted XTP FT HD 4K Fiber Transmitter • SIS Configuration and Control... -
Page 25: Configuration Software
Software This section contains installation and configuration procedures for the XTP System Configuration Software to configure and control the XTP FT HD 4K. The device can also be configured and controlled remotely through the XTP System Configuration Software and the XTP matrix switcher (see the XTP System Configuration Software Help file). -
Page 26: Software Product Page
Submit any required information to start the download. Note where the file is saved. Open the saved executable (.exe) file. Follow the instructions that appear on the screen to install the program. XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software... -
Page 27: Software Connection
Software Connection To connect the software directly to the XTP FT HD 4K, connect the computer running the software to the configuration connector (see figure on page 10). Figure 12. Connections Screen To connect to a device: Open the XTP System Configuration Software. The screen opens. -
Page 28: Software Operation
Backup and Restore Commissioning Report available when directly connected to the XTP FT HD 4K (see an XTP matrix switcher user guide (www.extron.com) for more information on these features). XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software... - Page 29 This option resets all disabled confirmation dialogs to the default settings. From the menu, select . The Tools Software Preference Software Preference dialog box opens. Figure 17. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software...
- Page 30 This option opens the XTP System Configuration Software help file in a web browser. From the menu, select Help Help Extron Website This option opens the Extron website in a web browser. From the menu, select Help Extron Website XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software...
-
Page 31: Transmitter Configuration
XTP receiver or XTP matrix switcher or deselect it to stop transmitting a test pattern to an XTP receiver or XTP matrix switcher. If selected, also select a signal type from the drop-down menu. Signal Type XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software... - Page 32 Selected Audio Input — Displays the audio format of the selected input. Audio only — Displays whether only audio is sent to outputs. Analog Audio Gain — Displays the gain for analog audio. XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software...
- Page 33 Navigate to and select the desired EDID file and click . The EDID file appears in the Open panel ( Available EDID Assign the EDID file from the panel to import the EDID to the device. Available EDID XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software...
- Page 34 Common Timings Connected Outputs listing the EDID settings common among the selected outputs. Select the desired common EDID. The EDID is shown in the panel. Available EDID XTP FT HD 4K Fiber Transmitter • XTP System Configuration Software...
-
Page 35: Reference Information
• Firmware Download Mounting The XTP FT HD 4K can be placed on a tabletop or mounted in a rack or underneath a desk. Tabletop Mounting Attach the provided rubber feet to the bottom four corners of the enclosure. Furniture Mounting Go to www.extron.com... -
Page 36: Firmware Download
The file can be downloaded from the same page as the firmware. Submit any required information to start the download. Note where the file is saved. XTP FT HD 4K Fiber Transmitter • Reference Information... - Page 37 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.