Page 1: Installation Instructions

Installation Instructions 30" Electric, 30" Induction Range 30", 36" All Gas Range 30", 36", 48" Dual Fuel Range To prevent accidents and damage to the range, you must read all instructions supplied before installing or using the appliance. en-US, CA M.-Nr.
Page 2: Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS  WARNING Children and adults can tip over the range if has not been secured. This may lead to fatal injuries.  This range must be secured and connected using the anti-tip device according to the installation instructions. ...
Page 3

IMPORTANT SAFETY INSTRUCTIONS  WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. – Do not use or store gasoline or other combustible liquids or vapors in the vicinity of this or any other appliance.
Page 4: Table Of Contents

Required connections ................... 21 Electric Range dimensions................. 22 HR 1421; HR 1622 ....................22 Detailed views of HR 1421 ..................24 Detailed views of HR 1622 ..................28 All Gas Range dimensions.................. 32 All Gas Range HR 11xx with Standard Burner Configuration (M Pro Power Plus)..
Page 5

Contents Detailed views of HR 1954 ..................83 Detailed views of HR 1955 ..................87 Detailed views of HR 1956 ..................91 Anti-tip device...................... 95 Before installation....................95 Checking the installation space ................96 Included accessories..................... 98 Installation dimensions of locking bolt ..............99 Installing the range with the anti-tip device............
Page 6: Important Safety Instructions

Both documents contain important information about installation, safety, use and maintenance. Miele cannot be held liable for damage occurring as a result of non-compliance with the instructions. Keep these installation instructions and operating instructions in a...
Page 7

IMPORTANT SAFETY INSTRUCTIONS  This range is intended for domestic use and use in other similar environments.  This appliance is not intended for outdoor use.  Use the range exclusively under normal domestic conditions: – Use the oven for baking, roasting, broiling, defrosting, canning and drying food.
Page 8

IMPORTANT SAFETY INSTRUCTIONS Children  Children must be kept away from the range unless constantly supervised.  Please supervise any children in the vicinity of the range and do not let them play with the appliance.  Burn hazard from improper use! Do not allow children to operate the oven.
Page 9

Technical safety  Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions. Contact Miele’s Technical Service Department for examination, repair or adjustment. Repairs and other work by unauthorized persons could be dangerous and may void the warranty.
Page 10

Risk of electric shock! If the ceramic surface of the stovetop is defective or chipped, cracked or broken in any way, immediately switch the stovetop off and do not continue to use it. Disconnect the range from the power supply and contact Miele Technical Service.
Page 11

IMPORTANT SAFETY INSTRUCTIONS  In order for the range to function properly, it requires an adequate supply of cool air. Ensure that the air flow is not impaired. Also be sure that the cool air supply is not excessively heated by other heat sources (e.g.
Page 12: Cleaning And Care

IMPORTANT SAFETY INSTRUCTIONS Preparing your appliance for an extended vacation  If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance.
Page 13: Notes On Installation

– Speed Oven load) for your range. – Warming Drawer Have this information available when – an anti-tip device including screws contacting Miele Technical Service. for fastening the range, Distance to the range hood – various accessories. The minimum clearance between the...
Page 14: Installation Of The Drip Tray

Notes on installation Installation of the drip tray The drip tray covers the gap between the oven cavity and the door.  Open the oven door.  Lay the drip tray over the gap between the oven cavity and the door.
Page 15: Assembling The Grill

Notes on installation Assembling the grill  Burn hazard! The burners must be turned off and allowed to cool completely.  Risk of injury! The cast-iron grill is heavy.  Place the grill  into position. Carry the grill carefully and place it Cleaning and care securely on a soft base so that it lies flat.
Page 16: Optional Accessories

Backguard All accessories and cleaning products listed in these instructions are designed The rear of the range must be to be used with the Miele range. accessible. These can be ordered from the Miele Install the backguard before installing website (see end of this booklet for the anti-tip device and connecting the contact details).
Page 17

Notes on installation a Backguard b Rear panel backguard c Inside panel  Place the backguard  face down on a soft surface to avoid scratching. The lower edge should line up with the edge of the table, so that the backguard lies flat.
Page 18

Notes on installation 20" Backguard  Once the backguard is placed on the range push the backguard backwards.  Install the inner panel and the rear panel on the backguard using the screws provided.  Install the backguard on the range using the screws provided.
Page 19: Rbs Backsplash

Notes on installation RBS Backsplash The backsplash is intended for installation to a Miele Range Hood (DAR model). Observe the installation instructions of the Miele Range Hood. XKM 3000 W Remote Vision (USA Only) Depending on the model, the range maybe compatible with...
Page 20

Due to the size and weight of the appliance, installation should be performed by two people. The net weight of the range with accessories is as follows: Model Width Net weight incl. accessories: HR 1421 29 15/16" approx. 307 lbs (140 kg) HR 1622 (760 mm) HR 112x HR 192x HR 113x 35 15/16"...
Page 21: Required Connections

Notes on installation Required connections Model Electrical Gas connection Plumbing connection HR 1421 – – HR 1622 – HR 112x – HR 113x HR 192x HR 193x HR 195x X Connection required – Connection not provided...
Page 22: Electric Range Dimensions

Electric Range dimensions HR 1421; HR 1622 , ,  The shaded area represents the installation area for the connections: E = Electrical connection, W = Water connection (only HR 1622)
Page 23

Minimum distance between the top of the cooking area and the bottom of an unprotected combustible surface. or 24" (609 mm) Minimum distance to a protected combustible surface or when a Miele Ventilation Hood is installed. For all other Hoods please consult the manufacturer's specifications for required distances.
Page 24: Detailed Views Of Hr 1421

Electric Range dimensions Detailed views of HR 1421 Side view of HR 1421 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 25

Electric Range dimensions Detailed front side view of HR 1421 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 26

Electric Range dimensions Front side view of HR 1421 (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 27

Electric Range dimensions Rear view of HR 1421 E = Electrical connection...
Page 28: Detailed Views Of Hr 1622

Electric Range dimensions Detailed views of HR 1622 Side view of HR 1622 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 29

Electric Range dimensions Detailed front side view of HR 1622 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 30

Electric Range dimensions Front side view of HR 1622 (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 31

Electric Range dimensions Rear view of HR 1622 E = Electrical connection W = Water connection...
Page 32: All Gas Range Dimensions

All Gas Range dimensions All Gas Range HR 11xx with Standard Burner Configuration (M Pro Power Plus) HR 1124, HR 1134, HR 1135, HR 1136 If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21. ...
Page 33

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). For all other Hoods please consult the manufacturer's specifications for required distances.
Page 34

36" (914 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). 30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower).
Page 35

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL or DRxB XXL blower). For all other Hoods please consult the manufacturer's specifications for required distances.
Page 36: All Gas Range Hr 11xx With Btu-reducing Kits

(M Pro Power - Zero Gap; M Pro - Décor Hood) HR 1124, HR 1134, HR 1135, HR 1136 For Miele Range-Hoods and Miele Range-Décor Hoods: If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21. Jets are a standard accessory and are getting changed during installation, see "Combination Range with BTU-reducing kit".
Page 37

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). Please refer to Miele ventilation hood installation manual. Appliance Dimensions section (Distance between cooktop and hood (S)).
Page 38

36" (914 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). 30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower).
Page 39

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL or DRxB XXL blower). Please refer to Miele ventilation hood installation manual. Appliance Dimensions section (Distance between cooktop and hood (S)).
Page 40: Detailed Views Of Hr 1124

All Gas Range dimensions Detailed views of HR 1124 Side view of HR 1124 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 41

All Gas Range dimensions Detailed front side view of HR 1124 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 42

All Gas Range dimensions Front side view of HR 1124 (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 43

All Gas Range dimensions Rear view of HR 1124 E = Electrical connection G = Gas connection...
Page 44: Detailed Views Of Hr 1134

All Gas Range dimensions Detailed views of HR 1134 Side view of HR 1134 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 45

All Gas Range dimensions Detailed front side view of HR 1134 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 46

All Gas Range dimensions Front side view of HR 1134 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 47

All Gas Range dimensions Rear view of HR 1134 E = Electrical connection G = Gas connection...
Page 48: Detailed Views Of Hr 1135

All Gas Range dimensions Detailed views of HR 1135 Side view of HR 1135 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 49

All Gas Range dimensions Detailed front side view of HR 1135 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 50

All Gas Range dimensions Front side view of HR 1135 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 51

All Gas Range dimensions Rear view of HR 1135 E = Electrical connection G = Gas connection...
Page 52: Detailed Views Of Hr 1136

All Gas Range dimensions Detailed views of HR 1136 Side view of HR 1136 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment:5" - 6 1/2" (127 mm - 165.1 mm)
Page 53

All Gas Range dimensions Detailed front side view of HR 1136 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 54

All Gas Range dimensions Front side view of HR 1136 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 55

All Gas Range dimensions Rear view of HR 1136 E = Electrical connection G = Gas connection...
Page 56: Dual Fuel Range Dimensions

Dual Fuel Range dimensions Dual Fuel Range HR 19xx with Standard Burner Configuration (M Pro Power Plus) HR 1924, HR 1934, HR 1935, HR 1936, HR 1954, HR 1955, HR 1956 If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21.
Page 57

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). For all other Hoods please consult the manufacturer's specifications for required distances.
Page 58

36" (914 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). 30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower).
Page 59

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL or DRxB XXL blower). For all other Hoods please consult the manufacturer's specifications for required distances.
Page 60

36" (914 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower). For all other Hoods please consult the manufacturer's specifications for required distances.
Page 61: Dual Fuel Range Hr 192x/193x With Btu-reducing Kits

(M Pro Power - Zero Gap; M Pro - Décor Hood) HR 1924, HR 1934, HR 1935, HR 1936 For Miele Range Hoods and Miele Range-Décor Hoods: If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21.
Page 62

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). Please refer to Miele ventilation hood installation manual. Appliance Dimensions section (Distance between cooktop and hood (S)).
Page 63

36" (914 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL blower). 30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower).
Page 64

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XL or DRxB XXL blower). Please refer to Miele ventilation hood installation manual. Appliance Dimensions section (Distance between cooktop and hood (S)).
Page 65: Dual Fuel Range Hr 195x With Btu-reducing Kit (m Pro Power - Zero Gap)

(M Pro Power - Zero Gap) HR 1954, HR 1955, HR 1956 For Miele Range Hoods: If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21. Jets are a standard accessory and are getting changed during installation, see "Combination Range with BTU-reducing kit".
Page 66

30" (762 mm) Minimum distance between the top of the cooking area and the bottom of the Miele Range Hood (DAR model with DRxB XXL blower). Please refer to Miele ventilation hood installation manual. Appliance Dimensions section (Distance between cooktop and hood (S)).
Page 67: Detailed Views Of Hr 1924

Dual Fuel Range dimensions Detailed views of HR 1924 Side view of HR 1924 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 68

Dual Fuel Range dimensions Detailed front side view of HR 1924 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 69

Dual Fuel Range dimensions Front side view of HR 1924 (x) = Depending on the appliance height adjustment 5" - 6 1/2" (127 mm - 165.1 mm)
Page 70

Dual Fuel Range dimensions Rear view of HR 1924 E = Electrical connection W = Water connection G = Gas connection...
Page 71: Detailed Views Of Hr 1934

Dual Fuel Range dimensions Detailed views of HR 1934 Side view of HR 1934 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 72

Dual Fuel Range dimensions Detailed front side view of HR 1934 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 73

Dual Fuel Range dimensions Front side view of HR 1934 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 74

Dual Fuel Range dimensions Rear view of HR 1934 E = Electrical connection W = Water connection G = Gas connection...
Page 75: Detailed Views Of Hr 1935

Dual Fuel Range dimensions Detailed views of HR 1935 Side view of HR 1935 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 76

Dual Fuel Range dimensions Detailed front side view of HR 1935 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 77

Dual Fuel Range dimensions Front side view of HR 1935 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 78

Dual Fuel Range dimensions Rear view of HR 1935 E = Electrical connection W = Water connection G = Gas connection...
Page 79: Detailed Views Of Hr 1936

Dual Fuel Range dimensions Detailed views of HR 1936 Side view of HR 1936 47 5/8" (1210mm) 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 1 3/4" (45mm) (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 80

Dual Fuel Range dimensions Detailed front side view of HR 1936 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 81

Dual Fuel Range dimensions Front side view of HR 1936 (x) = Depending on the appliance height adjustment: 5" - 6 1/2" (127 mm - 165.1 mm)
Page 82

Dual Fuel Range dimensions Rear view of HR 1936 E = Electrical connection W = Water connection G = Gas connection...
Page 83: Detailed Views Of Hr 1954

Dual Fuel Range dimensions Detailed views of HR 1954 Side view of HR 1954 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 15/16" (24.3mm) 44" (1114mm) (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 84

Dual Fuel Range dimensions Detailed front side view of HR 1954 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 85

Dual Fuel Range dimensions Front side view of HR 1954 (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 86

Dual Fuel Range dimensions Rear view of HR 1954 E = Electrical connection W = Water connection G = Gas connection...
Page 87: Detailed Views Of Hr 1955

Dual Fuel Range dimensions Detailed views of HR 1955 Side view of HR 1955 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 15/16" (24.3mm) 44" (1114mm) (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 88

Dual Fuel Range dimensions Detailed front side view of HR 1955 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 89

Dual Fuel Range dimensions Front side view of HR 1955 (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 90

Dual Fuel Range dimensions Rear view of HR 1955 E = Electrical connection W = Water connection G = Gas connection...
Page 91: Detailed Views Of Hr 1956

Dual Fuel Range dimensions Detailed views of HR 1956 Side view of HR 1956 28 15/16" (734.4mm) 27 1/4" (692mm) 24 15/16" (633mm) 15/16" (24.3mm) 44" (1114mm) (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 92

Dual Fuel Range dimensions Detailed front side view of HR 1956 2 3/8" (60mm) 1 9/16" (40mm) 1/8" (3mm) 1 1/4" (32mm) 1 3/4" (45mm) 2 9/16" (65.2mm)
Page 93

Dual Fuel Range dimensions Front side view of HR 1956 (x) = Depending on the appliance height adjustment: 4" - 5 1/2" (101.6 mm - 139.7 mm)
Page 94

Dual Fuel Range dimensions Rear view of HR 1956 E = Electrical connection W = Water connection G = Gas connection...
Page 95: Anti-tip Device

Anti-tip device Before installation We recommend removing the oven door before installing the range (see  WARNING "Removing the door" in the Operating Children and adults can tip over the Instructions) and all accessories from range if has not been secured. This the oven interior.
Page 96: Checking The Installation Space

Anti-tip device Checking the installation space Install the anti-tip device on a floor capable of bearing significant weight, such as a concrete floor, concrete wall or timber framing. The surface must be flat and level.  If the rear of the range has distance A to the supporting wall due to unevenness or wall covering (e.g., tile level), you must install the anti-tip device to the supporting floor.
Page 97

Anti-tip device  Check the diagrams for the building's supply lines. Make sure that you do not damage any lines when drilling the holes to attach the anti-tip device.  Check the position of the electric, gas and water connections (see "Electrical connection,"...
Page 98: Included Accessories

Anti-tip device Included accessories – 1 anti-tip device – 4 screws – 4 plugs...
Page 99: Installation Dimensions Of Locking Bolt

 Measure the installation space for the range close to floor level. Anti-tip device, front view  Mark the wall at the middle of the Model Width space width. HR 1421 29 15/16" 3 13/16"  Position the notch of the anti-tip HR 1622 (760 mm) (97 mm) bracket on the wall marking.
Page 100

Anti-tip device  Screw the locking nut  to the bolt, see the "Installation dimensions of locking bolt" table. Attaching to the floor Attaching to the wall a Anti-tip device b Screws c Locking nut  Secure the anti-tip device  to the floor surface with suitable bearing capacity, either to the floor or wall.
Page 101

Anti-tip device Do not push the range into Complete all necessary connections position before all supply for the range. Read the information in connections have been the "Electrical connection", "Gas established. connection" and "Plumbing" sections. The range can be damaged if it is The toe kick cover is attached to the lifted using the cover, the trim or the base of the range by magnets.
Page 102

Anti-tip device In the range housing, there is an Use a level to align the range. opening  for the bolt  of the anti-tip – Rear adjustment right  and left: device. The opening allows the range to You will need an open-end wrench be slid onto the anti-tip device and (3/8"...
Page 103: Disconnecting The Range From The Anti-tip Device

Anti-tip device Disconnecting the range from the anti-tip device  WARNING Children and adults can tip over the range if has not been secured. This may lead to fatal injuries. If you need to remove the range from its installation space, e.g. for service, you first need to disconnect the appliance from the anti-tip device.
Page 104: Electrical Connection

Miele-authorized service technician. Work by unqualified persons can cause considerable danger to users. Miele cannot be held liable for any damage arising as a result of such work. To avoid damaging the range, make...
Page 105: Data Plate

Electrical connection Electrical connection Type Connecting line NEMA Electrical supply Canada HR 1421 Approx. 5' 11" 14-50 P 120/208 V 50 A 40 A 60 Hz (1.80 m) plug 120/240 V HR 1622 Approx. 5' 11" 14-50 P 120/208 V...
Page 106

Installation, repair and maintenance work should only be performed by a Miele authorized service technician in compliance with local regulations and the ANSI National Electrical Code / NFPA 70 in the United States or the Canadian Electrical Code, Part I in Canada (CSA standard C22.1).
Page 107: Plumbing

Miele hose to do so (available from flooding. Miele will not be responsible Miele). The hose must be suitable for for any damages caused by supplying drinking water.
Page 108: Attach The Stainless Steel Hose To The Range

Plumbing Attach the stainless steel hose Connecting to the water supply to the range. Danger of electric shock! Disconnect the range from the Make sure that the stainless steel electrical supply before connecting it hose is not kinked or damaged. The to the water supply.
Page 109: Gas Connection

The gas connections must be The gas connection must be arranged in such a way that they are established only Miele-authorized not heated and damaged by the specialists according to the local and operation of the range. following regulations:...
Page 110

Gas connection The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The gas pressure may not undershoot or exceed certain values. Make sure that the maximum gas pressure upstream of the gas pressure controller does not amount to more than 1/2 psi (3.5 kPA) for...
Page 111: Burner Ratings Of Standard Burner Configuration

Burner ratings of Standard Burner Configuration Burner ratings for HR 1124 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Oven top burner Natural gas 22.000 6.45 Propane gas 20.150...
Page 112: Burner Ratings For Hr 1134

Burner ratings of Standard Burner Configuration Burner ratings for HR 1134 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Oven top burner Natural gas 22.000 6.45 Propane gas 20.150...
Page 113: Burner Ratings For Hr 1135

Burner ratings of Standard Burner Configuration Burner ratings for HR 1135 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Grill Natural gas 19.000 5.50 Propane gas 15.500 4.50 Oven top burner...
Page 114: Burner Ratings For Hr 1136

Burner ratings of Standard Burner Configuration Burner ratings for HR 1136 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Griddle Natural gas 13.000 3.80 Propane gas 14.300 4.20 Oven top burner...
Page 115: Burner Ratings For Hr 1934

Burner ratings of Standard Burner Configuration Burner ratings for HR 1934 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Total output of Natural gas 110.000 32.20 Cooktop Propane gas...
Page 116: Burner Ratings For Hr 1936

Burner ratings of Standard Burner Configuration Burner ratings for HR 1936 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Griddle Natural gas 13.000 3.80 Propane gas 14.300 4.20 Total output of...
Page 117: Burner Ratings For Hr 1955

Burner ratings of Standard Burner Configuration Burner ratings for HR 1955 Gas type BTU/hr Simmer burner Natural gas 12.500 3.70 Propane gas 12.500 3.70 Power burner Natural gas 19.500 5.70 Propane gas 19.500 5.70 Grill Natural gas 19.000 5.50 Propane gas 15.500 4.50 Total output of...
Page 118: Burner Ratings Of M Pro Power (zero Gap)

Burner ratings of M Pro Power (Zero Gap) When the BTU-reducing kit (Zero Gap) is used, the burner ratings of the burners change as follows: Gas type BTU/hr Simmer burner Natural gas 10.000 2.93 Propane gas 10.000 2.93 Power burner Natural gas 14.700 4.31...
Page 119: Burner Ratings Of M Pro (décor Hood)

Burner ratings of M Pro (Décor Hood) When the BTU-reducing kit (Décor Hood) is used, the burner ratings of the burners change as follows: Gas type BTU/hr Simmer burner Natural gas 10.000 2.93 Propane gas 10.000 2.93 Power burner Natural gas 12.200 3.58 Propane gas...
Page 120: Combination Range With Btu-reducing Kit

Combination Range with BTU-reducing kit If a BTU-reducing kit is necessary, an authorized installer is required to modify the product to meet ANSI Z21. Jets are a standard accessory and are getting changed during installation. Natural Gas BTU-reducing kit HR 1124 NG HR 113x NG HR 195x NG HR 1924 NG...
Page 121: Caring For The Environment

Consult with local authorities, dealers or Miele in order to dispose of and recycle electrical and electronic appliances. Miele assumes no responsibility for deleting any personal data left on the appliance being disposed.
Page 123

Technical Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Headquarters and Miele Centre Princeton, NJ 08540 161 Four Valley Drive Phone: 800-843-7231 Vaughan, ON L4K 4V8 609-419-4298 Fax: www.miele.ca www.mieleusa.com...
Page 124

All Electric: HR1421; HR1622; All Gas: HR1124; HR1134; HR1135; HR1136; Dual Fuel: HR1924; HR1934; HR1935; HR1936; HR1954; HR1955; HR1956  en-US, CA M.-Nr. 10 716 320 / 00...

This manual also for:

Hr 1622, Hr 112 series, Hr 193 series, Hr 195 series, Hr 113 series, Hr 192 series

Miele HR 1421 Installation Instructions Manual

Installation Instructions

Also See for Miele HR 1421

Related Manuals for Miele HR 1421

Summary of Contents for Miele HR 1421

This manual also for:

Comments to this Manuals

Latest comments: