Remaining Risks; Technical Specifications - Toolson dws225r Translation Of The Original Instructions

materials (e .g.lead paint, certain types of wood and
metaI) harmful or noxious dust may be generated.
Touching or breathing in such dust may imply risks
for the operator or people in the vicinity.
Notes regarding vibration and noise emissions
Reduce noise emissions and vibrations to a minimum!
1. Only use power tools which are free of defects.
2. Maintain and clean the power tool on a regular ba-
sis.
3. Adjust your way of working to the power tool.
4. Do not overload your power tool.
5.Have your power tool inspected, if necessary.
6. Switch off the power tool when it is not in use.

Remaining risks

Even if you use this power tool in compliance with
the regulations, there arestill remaining risks. The fol-
lowing risks may occur due to the type and design of
the power tool:
a) Damage caused to your health resulting from hand/
arm vibrations if the power tool is used over a Ionger
period of time or if it is not properly used and main-
tained.
b) lnjury and damage to property caused by flying off
insertion tools which are unexpectedly expelled from
the power tool due to sudden damage, wear or in-
correct insertion.
c) Burns and cuts if the insertion tools are touched di-
rectly after use and/or with your bare hands.
Warning! This electric tool generates an electromag-
netic field du ring operation which may impair active or
passive medical implants under certain circumstances.
ln order to reduce the risk of severe or Iethal injury, we
recommend that persons with medical implants consult
their doctor and the manufacturer of the medical im-
plant before using the power tool.

Technical Specifications

Dimensions LxWxH
mm
Round sanding
head
Triangular sanding
head
Oscillation: 3000-6000 1/min
Weight kg
Motor V/Hz
Input Power P1
Protection class
Sound pressure
level L
PA
Sound power level
L
WA
Vibration
Subject to technical changes!
Warning
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another. The decla-
red vibration total value may also be used in a prelimi-
450x270x210
Ø 225 mm
n: 1000-2200 1/min
edge length 280 mm
3,8
230 / 50
750W
II
91,3 dB(A),
K : 3 dB (A)
pA
102,3 dB(A),
K : 3 dB (A)
wA
a 7,66 m/s
2
h:
K: 1,5 m/s
2
nary assessment of exposure.
The vibration emission during actual use of the power
tool can differ from the declared total value depending
on the ways in which the tool is used. There is the
need to identify safety measures to protect the opera-
tor that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
Warning
This machine produces an electromagnetic field during
operation. This field may under some circumstances
interfere with active or passive medical implants. To
reduce the risk of serious or fatal injury, we recom-
mend persons with medical implants to consult their
physician and the medical implant manufacturer before
operating this machine .
Attaching/changing the sanding head
(Fig.2.1/2.2)
Before performing any work on the electric power tool,
pull out the main plug.
To attach:
1. Press the lock button on the side of the tool;
2. Put the tool on the sanding head and rotate to get the
correct position
3. Release the lock button to engage.
To change: Press the lock button on the tool change
head and remove sanding head. The triangular sanding
head is attached/changed in the same way. When atta-
ching the tool change head, ensure that the locks enga-
ge correctly.
Installation & Sandpaper Replacement
(Fig.3)
To ensure the replacement procedures, place the de-
vice on the smooth ground prior to installation. Take the
sandpaper from the toolbox, and then fix it onto the disk.
The back of the sandpaper (Item l) will automatically glue
with the disk/adhesive disk, making both connection and
conduction available . In order to promote the sanding
efficiency, it is necessary to change the sandpaper after
the device has been operational for a certain period.
Firstly, switch off the device and disconnect the socket.
Then, remove the previous sandpaper entirely from the
disk, so as to lay new sandpaper neatly as well as fa-
cilitate future replacement. At last, fix new sandpaper
in position.
For round sanding head only:
Conduct a test run to check that the sanding tool is
Clamped in the centre.
Sandpaper Overview
The Sandpaper is used for sanding the wall or objects
by its grains. The sandpaper is classified into various
categories according to its dimensions. It is recommen-
ded to select the sandpaper in accordance with actual
17 І 144