Mytee SPEEDSTER 1003DX Instruction Manual & Safety Manual

UNPACKING THE MACHINE
Speedster Extractor
Before unpacking the machine, inspect all boxes and pallets for signs of shipping damage.
Please be aware that all packages leave Mytee Products in perfect condition. Any equipment or
carton damage caused during shipping is the responsibility of the freight company, and should
be handled by filing a claim with the carrier.
H226 - 45O Drain Elbow
E530 - (2) 12/3 50'
H375 - Hose Hanger Yellow Safety Cord
SAFETY LABELS
The safety labels !
WARNING: Flammable materials can cause an
appear on the
explosion or fire. Do not use flammable materials in
machine in the
tank(s). Flammable materials or reactive metals can
locations indicated.
cause explosion or fire.
Replace labels if they
!
become damaged or WARNING LABEL- Located on back. Label warns
cannot be read. operator of safe practices of equipment.
SETUP
MACHINE COMPONENTS
1. Open lid of solution tank. Fill solution tank with
Recovery
water or approved cleaning agent.
Tank
Vacuum ! WARNING: Flammable materials can cause an
Hose explosion or fire. Do not use flammable solutions or
Solution
Connector materials in tank(s).
Tank
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
Motor
Solution
Housing/
Hose
ATTENTION: If using powdered cleaning chemicals,
Base
Connector mix prior to adding.
2. Attach solution hose. (Located front of machine.)
NOTE: Make sure the quick disconnects snap
together firmly. As you do this, always inspect
hoses for cracks or fraying. Do not use if hoses are
damaged.
Pressure
Regulator
3. Attach other end of solution hose to wand.
Prime Valve 4. Attach vacuum hose to recovery tank.
5. Plug machine's cord into a grounded wall outlet.
PRE-OPERATION
FOR SAFETY: Do not operate machine unless cord is
1. Vacuum carpet and upholstery and remove
properly grounded.
other debris.
2. Perform MACHINE SETUP procedures. FOR SAFETY: Do not operate machine with the use
of an extension cord.
3. Inspect power cord for damage.
OPERATION
WEEKLY MAINTENANCE
7. Turning machine on. (EVERY 20 HOURS OF OPERATION)
A. Turn pump switch on.
1. Flush solution system with Mytee system
B. Pull up on power prime lever for 30 seconds. maintainer to dissolve normal chemical buildup.
This will prime the pump. a. Pour 7.5L (2 gal) of hot water 60°C
(140°F) into solution tank. Add Mytee
C. Pull up on wand lever to release air in the
system maintainer according to mixing
line. Hold lever until you have a steady flow of
instructions on bottle
water coming out of the wand.
D. Once pump is primed and you have pressure
FOR SAFETY: When using machine, follow
in the solution line, turn on heater switch(s) (if
mixing and handling instructions on chemical
model is equipped with heater) and wait a few
containers.
minutes for water to heat up.
E. Once water is heated, turn on vacuum
b. Operate machine for one minute.
motors and begin cleaning.
c. Shut off machine and allow remaining
solution to break down chemical buildup
NOTE: When cleaning upholstery, always check
overnight.
manufacturer's cleaning instructions.
d. Next day, spray out remaining
TIPS
solution and flush system with 11L (3gal)
1. Work away from outlet and power cord to prevent cord of clean water.
damage.
2. Inspect vacuum hoses for holes and loose
2. Use a recommended foam control solution in the
cuffs. Drain and dry the vacuum hose as well.
recovery tank to prevent vacuum motor damage.
Periodically check for excessive foam buildup in solution
3. Inspect spray pattern for clogging. If
tank, and recovery tank.
clogged, remove spray tips and soak them in
3. To clean heavily soiled areas, repeat cleaning path from a recommended liquid neutralizer for up to six
hours. To remove spray tip, twist spray tip body
different direction.
counter-clockwise.
4. When ball float shuts off vacuum, it is time to empty the
dirty water from the recovery tank, and refill solution tank.
4. Lubricate wheels with water resistant oil.
5. After cleaning, relieve water pressure from tool before
5. Inspect machine for water leaks and loose
disconnecting hose. Squeeze trigger for five seconds
hardware.
after turning main power switch off.
MAINTENANCE
6. Remove float shut-off screen from recovery
tank and clean.
FOR SAFETY: When servicing machine, unplug cord from
wall outlet.
NOTE: The float shut off screen is not glued on.
1. Turn machine off and unplug power cord. Simply pull it off.
2. Remove solution & vacuum hose.
STORING MACHINE
3.Attach 45º-drain elbow to dump valve and lift up drain
1. Before storing machine, be certain to
valve lever to empty recovery tank.
completely drain and rinse tanks of all water and
DRAINING RECOVERY TANK
solution.
MACHINE MAINTENENCE
2. Drain and dry the vacuum hose as well, using
To keep machine in good working condition, simply follow
the drain hose provided
machine's daily and weekly maintenance procedures.
Check valves and relief valves should be replaced
3. Store machine in a dry area in the upright
annually.
position.
FOR SAFETY: When servicing machine, unplug cord from
4. Open recovery tank cover to promote air
wall outlet.
circulation
DAILY MAINTENANCE
ATTENTION: Do not expose to rain. Store indoors.
1. Empty and rinse out solution tank thoroughly.
2. Wipe off power cord and check for damage, replace if
ATTENTION: If storing machine in freezing
necessary. Coil cord neatly after use. temperatures, be sure that machine and solution
system are completely drained and dry.
3. Clean machine with an all purpose cleaner and damp cloth.
SPEEDSTER
1003Dx
Instruction Manual
& Safety Guide