1. Manuals
  2. Brands
  3. Matrix Manuals
  4. Gateway
  5. SIMADO GFX44
  6. System manual

Matrix SIMADO GFX44 System Manual

Fixed gsm/3g to analog voice gateway
Hide thumbs Also See for SIMADO GFX44:
Table of Contents

Advertisement

Quick Links

SIMADO GFX44
System Manual
Magyarországon a Matrix Telecom Ltd. képviselete,
Matrix termékek importőre, kizárólagos forgalmazója:
1095 Budapest, Mester u. 34.
Telefon: *218-5542, 215-9771, 215-7550, 216-7017, 216-7018
Fax: 218-5542 Mobil: 30 940-1970, 20 949-2688
E-mail: delton@delton.hu Web: www.delton.hu

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIMADO GFX44 and is the answer not in the manual?

Questions and answers

Related Manuals for Matrix SIMADO GFX44

Summary of Contents for Matrix SIMADO GFX44

  • Page 1 SIMADO GFX44 System Manual Magyarországon a Matrix Telecom Ltd. képviselete, Matrix termékek importőre, kizárólagos forgalmazója: 1095 Budapest, Mester u. 34. Telefon: *218-5542, 215-9771, 215-7550, 216-7017, 216-7018 Fax: 218-5542 Mobil: 30 940-1970, 20 949-2688 E-mail: delton@delton.hu Web: www.delton.hu...
  • Page 2 Neither Matrix Telecom nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs or expenses incurred by purchaser or third parties as a result of:...

  • Page 3: Table Of Contents

    Contents Section 1: Introduction ..............5 Welcome ..................7 Packing List ................. 9 Warranty Statement ..............10 Introducing the System .............. 13 Protecting the System ............... 15 Getting Started ................17 Section 2: Features and Facilities ..........25 Allowed and Denied Lists ............27 Answer Signaling on FXS Port ..........
  • Page 4 Routing Type ................116 Signal Strength ................ 129 SIM PIN ..................130 Software Version/Revision ............133 Time Table ................134 Section 3: Appendices ............. 137 Appendix A: Applications ............139 Appendix B: Technical Specifications ........141 Appendix C: System Commands ..........143 Appendix D: Regulatory Information ........

  • Page 5: Section 1: Introduction

    Section 1: Introduction...

  • Page 7: Welcome

    Matrix dealers are trained and ready to give you the support you need to get the most from your Matrix product. In fact, most problems reported are minor and can be easily solved over the phone.
  • Page 8 • SIM PIN The words ‘GSM’ and ‘Mobile’ are synonymous and are used interchangeably in the manual. The words ‘SIMADO GFX44’ and ‘System’ are used interchangeably in the manual. The user can use the pages named ‘Notes’ given at the end of the system manual for making note of customer’s requirements...

  • Page 9: Packing List

    Matrix Packing List The ideal sales package for SIMADO GFX44 is as mentioned below: Accessories Qty. SIMADO GFX44 System Manual 3 Pin Power Cord, MC-4 Black Wall Mounting Nails Warranty Card Set Support Card COM Port Cable (RS232C) Mounting Template...

  • Page 10: Warranty Statement

    12 months from the date of installation which ever is earlier. During this warranty period, Matrix will at its option, repair or replace the product at no additional charge if the product is found to have manufacturing defect. Any replacement product or part/s may be...
  • Page 11 The Purchaser shall have to either insure the product or assume liability for loss or damage during transit. Matrix reserves the right to waive or make any changes in its warranty policy without giving any notice. If Matrix is unable to repair or replace, as applicable, a defective...
  • Page 12 This warranty is not transferable and applies only to the original consumer purchaser of the Product. Warranty shall be void if the warranty card is not completed and registered with Matrix within 30 days of installation. SIMADO GFX44 V1 System Manual...

  • Page 13: Introducing The System

    Matrix Introducing the System • Matrix product SIMADO GFX44 is a versatile analog gateway. • It is a multi channel GSM Gateway, a solution for medium size companies that widely use GSM lines. • It makes possible up to 4 simultaneous calls to the GSM network.
  • Page 14 Matrix SIMADO GFX44 Photograph: =X=X= SIMADO GFX44 V1 System Manual...

  • Page 15: Protecting The System

    • Do not allow anything to rest on the power cord of product or AC- DC Adapter. Do not place this product where the cord will be misused by people walking on it. • Do not overload wall outlets and extension cords as this can SIMADO GFX44 V1 System Manual...
  • Page 16 If the product has been dropped or the cabinet has been damaged. f) If the product exhibits a distinct change in performance. • Do not use the telephone of the product to report a gas leak in the vicinity of the leak. =X=X= SIMADO GFX44 V1 System Manual...

  • Page 17: Getting Started

    Matrix Getting Started Overview The Matrix SIMADO GFX44 allows you to call GSM number from the normal analog phone and establish a voice call. Total of four such calls can be established. It can be four GSM calls for different service provider network.
  • Page 18 • Basic steps for configuration. • Making phone calls. Getting to know the GFX44 This Matrix GFX44 has some ports located on the rear panel and LED’s with SIM card slots located on the right side panel, as shown below: •...
  • Page 19 • After the reset cycle is completed, the ports are under different states. There may be a ring event on the port or may be an Outgoing call event on the port. Accordingly, respective LED is glowing. The Gateway supports following LED Indications during SIMADO GFX44 V1 System Manual...
  • Page 20 GSM module will not be detected. Port Disabling: In case if any Port is disabled, system supports following Cadence for the concerned LEDs: SIMADO GFX44 V1 System Manual...
  • Page 21 Instruction for Connecting Interfaces: This section describes the instructions on how to connect the Matrix GFX44 to GSM network and analog telephones. • Unpack the box. Get satisfied with the contents and the condition of the parts. Refer to Packing List. If parts are OK, proceed with connections as mentioned below.
  • Page 22 • Make sure that your GS M m odule is registered with GSM network • Default the gateway by dialing 292-4321-#*. You can now call any number from the GSM port. • You can use the gateway features by two ways: SIMADO GFX44 V1 System Manual...
  • Page 23 • For programming through Windows based software, install the CD provided with the product, to your PC. Click on Start Programs Matrix SIMADO GFX44 Jeeves V1R2. Enter the ‘Password’, ‘1234’ to start programming. Refer chapter ‘Jeeves’ in manual. • For operating GFX44, using commands, enter the programming mode by;...
  • Page 24 Matrix Mechanical Dimension of SIMADO GFX44 50 millimeters 155 millimeters (6.10 Inch) (1.97 Inch) SIMADO GFX44 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 25: Section 2: Features And Facilities

    Section 2: Features and Facilities...

  • Page 27: Allowed And Denied Lists

    Allowed and Denied Lists What’s this? • The SIMADO GFX44, supports a feature by which the system can prevent selected numbers to be dialed out, known as Allowed and Denied Lists. For this, the feature should be enabled for the port.
  • Page 28 By default, Number List 01 is assigned to the FXS port. Use the following command to assign allowed number list to all the FXS ports: 111-*-Number List-#* Step 2 Use following command to assign a denied number list to a FXS port: SIMADO GFX44 V1 System Manual...
  • Page 29 By default, Number List 06 is assigned to the Mobile Port. Use following command to assign a denied number list to all the mobile ports: 114-*-Number List-#* Step 5 Use following command to enable/disable allowed/denied logic on FXS port: SIMADO GFX44 V1 System Manual...
  • Page 30 101-08-03-94-#* (Mobile Number 94 programmed in list 08) 112-1-08-#* (Assign list 08 as denied list to FXS1) 102-06-#* (Clear No. list 06, assigned to FXS1, by default) 102-01-#* (Clear No. list 01, assigned to FXS1, by default) SIMADO GFX44 V1 System Manual...
  • Page 31 Matrix Relevant Topic: 1. Number Lists =X=X= SIMADO GFX44 V1 System Manual...

  • Page 32: Answer Signaling On Fxs Port

    For example, if the battery polarity of the FXS port is +ve for TIP and -ve for RING in speech condition then after call maturity, TIP will become -ve and Ring will become +ve. SIMADO GFX44 V1 System Manual...
  • Page 33 By default, Polarity Reversal for all ports. Use following command to program the signal to be generated as Answer Signaling on all FXS port: 261-*-Answer Signal-#* Related Topic: 1. Disconnect Signaling on FXS Port 64 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 34: Answer-Number Based Routing

    Matrix Answer-Number Based Routing What’s this? • SIMADO GFX44, has the facility to initiate the call from a specific port based on the number string dialed. This is called Answer- Number Based Routing. • For this, a separate routing group is assigned for a specific number string and the Member of the group will be the ports for dialing the Number.
  • Page 35 (0223) and routing group number is programmed as 2 at index 01. • If local calls made to City B’s number starting with 95792..using routing group number 2, then the dialed number string is SIMADO GFX44 V1 System Manual...
  • Page 36 (Assign selection a first free to routing group 1) 202-2-2-#* (Assign selection a first free to routing group 2) 202-3-3-#* (Assign selection a first free to routing group 3) Relevant Topics: 1. Routing Group 2. Routing Type =X=X= SIMADO GFX44 V1 System Manual...

  • Page 37: Automatic Number Translation

    User can use ANT for dialing international number also. For this ‘+’ sign has to be programmed in the substitute number list. It can be done by entering ‘#8’ from the telephone keypad. For example, +91266 can be entered by string #891266. SIMADO GFX44 V1 System Manual...
  • Page 38 FXS Port is from 1 to 4. Number List is from 01 to 16. By default, Number List 06 is assigned to the FXS Port. Use following command to assign a Substitute number list to all FXS ports: 122-*-Number List-#* SIMADO GFX44 V1 System Manual...
  • Page 39 Use following command to enable/disable automatic number translation logic on FXS port: 125-FXS Port-Code-#* Where, FXS Port is from 1 to 4. Code Meaning Disable Enable By default, Automatic Number Translation logic on all FXS ports is enable. SIMADO GFX44 V1 System Manual...
  • Page 40 101-05-01-91-#* (Program 91 at index 1 of number list 05, substitute number list) 123-1-03-#* (Assign dialed-number list to mobile port 1) 124-1-05-#* (Assign substitute number list to mobile port Relevant Topic: 1. Number Lists =X=X= SIMADO GFX44 V1 System Manual...

  • Page 41: Call Detail Recording (Cdr)

    Matrix Call Detail Recording (CDR) What’s this? • The SIMADO GFX44, supports a facility to store the details of calls made through the Gateway. This is called Call Detail Recording (CDR). User will program ‘enable’ option of filter, to apply the filter programmed.
  • Page 42 Default Filters for CDR are All FXS Ports, All GSM Ports, Date from 01-01-2006 to Current date, Time 00:00 to 23:59, Caller Number List 01, Called Number List 01, Duration more than 001 sec. By default, CDR report are Blank. SIMADO GFX44 V1 System Manual...
  • Page 43 150-Reverse SE Password-#* Step 3 Use following command to enable/disable the filter setting for calls terminated on FXS port: 141-Code-#* Where, Code Meaning Disable Enable By default, Filter setting for calls terminated on FXS port is enable. SIMADO GFX44 V1 System Manual...
  • Page 44 144-Code-#* Where, Code Meaning Disable Enable By default, Filter setting for calls originated on Mobile port is enable. • Called party number and Destination Port can be found when a call terminates on a port. SIMADO GFX44 V1 System Manual...
  • Page 45 • CDR records will be stored in the system permanently, only after 5 minutes (approx.). Do not restart the system before saving. Relevant Topics: 1. Communication Port 2. Allowed and Denied Lists 27 3. Routing Type 4. Jeeves 82 SIMADO GFX44 V1 System Manual...
  • Page 46 FXS 4 01-Jul-2007 09:27:53 6 FXS 4 FXS 2 01-Jul-2007 09:28:32 7 FXS 2 MOB 2 9898091380 01-Jul-2007 09:39:59 8 FXS 2 MOB 2 9824981745 01-Jul-2007 09:49:43 -------------------------------------------------------------------------------- Matrix SIMADO GFX44 V1R3 Page: 01 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 47: Call Proceeding Tone

    How to program? Use following command to set Call Proceeding Tone for mobile port: 277-CPT Type-#* Where, CPT Type Meaning Feature Tone (SIMADO Tone) GSM Network Tone By default, Call Proceeding Tone is ‘2’. SIMADO GFX44 V1 System Manual...
  • Page 48 Matrix Relevant Topic: 1. Call Progress Tone Generation =X=X= SIMADO GFX44 V1 System Manual...

  • Page 49: Call Progress Tone Generation (Cptg)

    Matrix Call Progress Tone Generation (CPTG) What’s this? • The SIMADO GFX44 supports generation of different types of tones to indicate the response for various events while establishing a call. These tones are called Call Progress Tone Generation (CPTG). The tones are generated in response to dialing of codes and commands.
  • Page 50 ON-Hook or dial a command. CCWT When an incoming call arrives while the user is connected to another party, this tone is played by the system. Use the following command to program the CPTG for a country: 281-Code-#* Where, SIMADO GFX44 V1 System Manual...
  • Page 51 Matrix Remarks: • f1*f2 : ‘f1’ is modulated by ‘f2’. • f1+f2 : Two frequencies without modulation. =X=X= SIMADO GFX44 V1 System Manual...

  • Page 52: Clip Type On Fxs Port

    CLIP Type on FXS Port What’s this? • SIMADO GFX44 provides a facility to detect the name and number of the calling party and present it to the FXS port. This is called Calling Line Identification and Presentation. The CLI data can be presented on LCD of the telephone instrument.
  • Page 53 Important Point: • This command is of help when a Telephone instrument connected to the FXS port is capable of sensing only one type of information. Relevant Topics: 1. Software Version/Revision 2. FXS Port Parameters =X=X= SIMADO GFX44 V1 System Manual...

  • Page 54: Communication Port

    Matrix Communication Port What’s this? • The SIMADO GFX44 supports a communication port which is used for following purpose: • To send the Call Detail Recording (CDR) to the computer. • For programming through Jeeves. • Based on application, a process is assigned to the COM port.
  • Page 55 Call Detail Recording By default, COM port is assigned the process ‘2’. Example: To assign COM port for taking CDR report, use following command: 310-3-#* Use the following command to start and stop the system debug: 309-Code-#* SIMADO GFX44 V1 System Manual...
  • Page 56 Matrix Where, Code Meaning Stop Start By default, System debug is 0. Relevant Topics: 1. Call Detail Recording (CDR) 41 2. Jeeves 82 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 57: Daylight Saving Time

    Step 4: Program to select DST Backward Type using command 324. Step 5: Program to set time for Week-Day-Month for DST Backward Type using command 325. Step 6: Program to set time for Date-Month-Hour-Minute for DST Backward Type using command 326. SIMADO GFX44 V1 System Manual...
  • Page 58 For e.g. In New Zealand, the DST starts on Last Sunday of October. The clock changes from 02:00 to 03:00. Following command should be issued to effect DST in New Zealand. 322-5-1-10-02-00-03-00-#* Step 3 Use following command to set time for Date-Month for DST forward type: SIMADO GFX44 V1 System Manual...
  • Page 59 If the month has 4 Sundays in a particular Calendar year then the last Sunday would be automatically the fourth one and if the month has 5 Sundays in a particular month of the Calendar year then the last Sunday would be automatically the fifth one). SIMADO GFX44 V1 System Manual...
  • Page 60 23:59 (00:00 midnight of 1st October) to 23:00. This means that DST should be changed on 30 Sept. at 23:59 to 23:00. Following command should be issued by the SE to effect DST. 326-30-09-23-59-22-59-#* SIMADO GFX44 V1 System Manual...
  • Page 61 • For e.g. In Chile, DST is reverted back to normal on second Sunday of March at 00:00 to Second Saturday of March 23:00. To effect this, user has to use following command: 325-2-7-03-23:59-22:59-#* Relevant Topics: 1. Real Time Clock (RTC) 2. Time Table =X=X= SIMADO GFX44 V1 System Manual...

  • Page 62: Default The Configuration

    • Serial COM Port Application Assignment. • FXS Port Parameters. • Mobile Port Parameters. • Routing Groups. • Number Lists. • CDR Filters. • Dialed-Number String Table. • Time Table. • DST Parameters. • Clear RCOC Entries. SIMADO GFX44 V1 System Manual...
  • Page 63 • The SE password gets default to 1234. Important Point: • SIM PIN and RTC is not assigned any default value while issuing system default command. Relevant Topics: 1. Getting Started 2. Programming the System =X=X= SIMADO GFX44 V1 System Manual...

  • Page 64: Disconnect Signaling On Fxs Port

    Signal assigned to the FXS port from where call has been made. The options for Disconnect Signaling are mentioned below: • None: It is used when no signaling is to be generated on FXS for call disconnection. When call is disconnected, user will get Error tone. SIMADO GFX44 V1 System Manual...
  • Page 65 How to program? Disconnect Signal: Use following command to program the Disconnect Signal to be generated on FXS port during IC and OG call: 256-FXS Port-Disconnect Signal-#* Where, FXS Port is from 1 to 4. SIMADO GFX44 V1 System Manual...
  • Page 66 Open Loop Disconnect Timer is from 001 to 999 ms. By default, 500ms for each port. Use following command to program the Open Loop Disconnect timer on all FXS port: 257-*-Open Loop Disconnect Timer-#* Related Topic: 1. Answer Signaling on FXS Port 32 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 67: Emergency Number Dialing

    This is known as ‘Emergency Number Dialing’. • SIMADO GFX44 supports this feature Mobile port. It may happen that you need to call emergency number even when you have not inserted the SIM card and the GSM module is not registered with the network.
  • Page 68 Step 1: Program emergency Number at an index using command 233. Step 2: Program routing group at on index using command 234. Step 1 Use the following command to program the emergency number in the table: SIMADO GFX44 V1 System Manual...
  • Page 69 (Program Routing Group Number 4) 234-2-3-#* (Program Routing Group Number 3) Now, program the routing group 4 such that Mobile port 1 is the first member and selection is first free type. Similarly program routing SIMADO GFX44 V1 System Manual...
  • Page 70 GSM module, or in the SIM in the memory storage, which is classified as emergency number. For this information, contact your GSM Service Provider. Relevant Topic: 1. Mobile Port Parameters =X=X= SIMADO GFX44 V1 System Manual...

  • Page 71: End Of Dialing Digit

    Digit as ‘#’. • Because of this feature the dialing is faster and will not wait for expiry of Inter Digit Wait Timer to end the dialing of digits. Relevant Topic: 1. FXS Port Parameters =X=X= SIMADO GFX44 V1 System Manual...

  • Page 72: Fixed Dialing

    What’s this? To avoid dialing of a station number or destination number which is frequently used, the Matrix system offers, a feature by which the user has to just pick up his handset and the system will automatically dial out the fixed destination number. This feature is called Fixed Dialing.
  • Page 73 175-Mobile Port-Code-#* Where, Mobile Port is from 1 to 4. Code Meaning Disable Enable By default, Fixed Dialing is enabled on all the ports. Use following command to enable/disable fixed dialing on all mobile ports: 175-*-Code-#* SIMADO GFX44 V1 System Manual...
  • Page 74 (For FXS1 routing type is Answer-Number Based and routing group is 4 by default. Hence program Mobile Port 1 as a member at index 1) 202-4-1-#* (Member selection as first free) Relevant Topics: 1. Routing Type 2. Routing Group =X=X= SIMADO GFX44 V1 System Manual...

  • Page 75: Fxs Port Parameters

    This can be done by providing different ring types for two stations. These features can be obtained by suitable programming of FXS port. The SIMADO GFX44 provides a facility in which FXS port can be programmed for following parameters: •...
  • Page 76 Step 2 Ring Type • During an incoming call, SIMADO GFX44 plays the ring over SLT, as per the ring cadence specified for the country. For example, ring for India is ‘Double’, whereas for Canada or US it is ‘Long Slow’.
  • Page 77 By default, Inter Digit Wait Timer is 04 seconds. Use following command to set inter digit wait timer for all FXS ports: 253-*-Inter Digit Wait Timer-#* Step 4 Flash Timer-This command is used to program the flash timer for SIMADO GFX44 V1 System Manual...
  • Page 78 FXS Port, is very far from the gateway site, the Tx level will be required to increase. Use following command to program Tx Gain on FXS port: 258-FXS Port-Code-#* Where, FXS Port is from 1 to 4. SIMADO GFX44 V1 System Manual...
  • Page 79 FXS port is notmatching to that of FXS port, then it may result to signal loss. To avoid such problem, AC Impendance is kept programmable. Use following command to program AC Impedance on FXS port: 260-FXS Port-Code-#* SIMADO GFX44 V1 System Manual...
  • Page 80 Otherwise user will get ‘Error tone’. The programming of AC impedance should be done only when FXS port is ‘Idle’. Relevant Topics: 1. End of Dialing Digit 2. CLIP Type on FXS Port =X=X= SIMADO GFX44 V1 System Manual...

  • Page 81: International Mobile Equipment Identity (Imei)

    Important Point: • Sometimes it may happen that module does not send the IMEI number during power ON. In such case, the user should restart the system. Relevant Topic: 1. Mobile Port Parameters =X=X= SIMADO GFX44 V1 System Manual...

  • Page 82: Jeeves

    Jeeves What’s this? • Programming a system through phones, is a bit time consuming process. The Matrix system provides a facility to program it using computer. • Matrix supplies a customized, windows based software to program the SIMADO GFX44, known as Jeeves.
  • Page 83 Jeeves) Download the existing System configuration on the Jeeves if needed. Make necessary changes in the configuration parameters Up load the modified configuration on to the System Verify by checking various features on the System SIMADO GFX44 V1 System Manual...
  • Page 84 The COM port is assigned to Jeeves using specific command. Example: To dial Mobile number ‘9898507330’ from ‘Mobile-1’ using Routing Group number-1 • The Jeeves screen for ‘GFX44’ looks as shown below: • Main Menu screen looks as shown below: SIMADO GFX44 V1 System Manual...
  • Page 85 • Click on ‘Mobile Parameters’ from main Menu. Enable ‘Fixed dialing’ for Mobile-1 port. Program the Mobile Number ‘9898507330’ in the ‘Fixed Destination Number’ field. Relevant Topics: 1. Communication Port 2. Programming the System =X=X= SIMADO GFX44 V1 System Manual...

  • Page 86: Mobile Port Parameters

    • In order to interface Mobile ports with GSM network, few parameters are required to be programmed. The SIMADO GFX44 provides a facility in which mobile port parameters can be programmed for following parameters: •...
  • Page 87 Mobile Port is from 1 to 4. Receive Gain Meaning Very Low Normal High Very high By default, Receive Gain is 3. Use following command to program the receive gain of all the mobile ports: 272-*-Receive Gain-#* SIMADO GFX44 V1 System Manual...
  • Page 88 Inter Digit Wait Timer is from 01 to 99 secs. By default, Inter Digit Wait Timer is 04 secs. Use following command to program inter digit wait timer for all the mobile ports: 274-*-Inter Digit Wait Timer-#* SIMADO GFX44 V1 System Manual...
  • Page 89 Use following command for selection of Mobile Frequency Band on all Mobile Ports: 278-*-Mobile Frequency Band-#* For example: Program 850 + 1900 GSM frequency band for countries which support both 850 and 1900 MHz frequencies for GSM network. SIMADO GFX44 V1 System Manual...
  • Page 90 GSM Module. It is 150 second. Relevant Topics: 1. Emergency Number Dialing 2. International Mobile Equipment Identity 3. Network Selection 4. SIM PIN 5. RCOC 6. Call Proceeding Tone 7. Signal Strength =X=X= SIMADO GFX44 V1 System Manual...

  • Page 91: Network Selection

    • User can assign option for network selection to each mobile port he wants to use. • The feature works, when SIMADO GFX44 is powered ON or if the port is NOT registered with network. • Maximum 9 network operators can be programmed. In Manual Mode mobile port starts to get registered with network operator, as per order of programming with its network operator code.
  • Page 92 : 505 • Italy : 222 How to program? Network selection feature can be programmed for SIMADO GFX44, using following steps: Step 1: To select network selection mode Manual or Automatic using command 231. Step 2: To program network operator’s code with priority using command 232.
  • Page 93 Mobile Network Operator Priority Port Number Blank Blank Blank Use the following command to clear network operator number: 232-Mobile Port-Priority-#* Where, Mobile Port is from 1 to 4. Priority is from 1 to 9. SIMADO GFX44 V1 System Manual...
  • Page 94 ‘Z’ (MCC 404, MNC 21) is little cheap for call charges. Then program the network operator as per priority, as shown below: He should program the SIMADO GFX44, for manual mode which doesn’t depend on field strength of the network. He makes the call from mobile port 3.
  • Page 95 • If user reattempts at every two minutes, then he is sure that the port will get registered and the system will be functional. Relevant Topic: 1. Mobile Port Parameters =X=X= SIMADO GFX44 V1 System Manual...

  • Page 96: Number Lists

    GFX44 use these lists to allow/deny a number dialed from the port as well as for automatic number translation. • SIMADO GFX44 supports 16 number lists. • Each number list has 24 entries, which can be referred to as location.
  • Page 97 04 can be programmed as: 102-04-#* (To clear all location) 101-04-01-0-#* (Program list with 0 prefix) Assign this list as denied list number to all FXS ports. Relevant Topics: 1. Allowed and Denied Lists 2. Automatic Number Translation =X=X= SIMADO GFX44 V1 System Manual...

  • Page 98: Programming The System

    Matrix Programming the System What’s this? • SIMADO GFX44, supports two methods of programming: • Programming with analog phones, connected at FXS ports. • Programming using Jeeves. Refer chapter Jeeves for this. • This chapter explains how to enter programming mode for applying various commands.
  • Page 99 • The commands are accepted even during confirmation tone. • You will get programming tone on expiry of the confirmation tone. Relevant Topics: 1. Jeeves 2. Routing Type 3. Default the Configuration 62 4. Communication Port =X=X= SIMADO GFX44 V1 System Manual...

  • Page 100: Real Time Clock (Rtc)

    • Such facilities work properly only if the system is set with correct date and time values. • For this SIMADO GFX44 is equipped with built in Real Time Clock (RTC) circuit. This circuit is to be set once with current date and time values.
  • Page 101 • RTC doesn’t get default, when system is default. • This will be defaulted only by loading new version and revision of the software. Relevant Topics: 1. Time Table 2. Daylight Saving Time 57 3. RCOC 4. CLIP Type on FXS Port =X=X= SIMADO GFX44 V1 System Manual...

  • Page 102: Remote Programming

    Matrix Remote Programming What’s this? SIMADO GFX44 supports programming of gateway from remote station. How it works? • To program the system remotely, the port should be programmed for Routing Type = Answer Number Based or Answer Fixed. Refer Routing Type chapter flow chart for more details.

  • Page 103: Restart The System

    • Many times it is difficult to physically walk to the system and restart it. It is convenient if we could do the same from telephone instrument. • The SIMADO GFX44 offers facility to restart the system by dialing a code. How to program?

  • Page 104: Returned Calls To Original Callers (Rcoc)

    Matrix Returned Calls to Original Callers (RCOC) What’s this? • The SIMADO GFX44 provides a facility to detect the calling party number and present it to the user on the LCD of the telephone instrument. • When a call is made to a mobile user and if he is found busy/not responding, the calling party’s number gets stored in the memory...
  • Page 105 • Call originates from FXS1 (2001) and gets terminated on GSM network on 9898000001, external number using mobile port 3 of the Gateway. Calling Party Called Party Originating S/w Port Number Number Number 2001 9898000001 FXS 1 SIMADO GFX44 V1 System Manual...
  • Page 106 System will fetch the originating System selects routing type on the port from RCOC database basis of timezone (Note 1) Is the port free? Call is placed on originating port Call is not answered found from RCOC database SIMADO GFX44 V1 System Manual...
  • Page 107 Code Meaning Disable Enable By default, Returned Calls to Original Callers for Busy Destination on a Mobile Port is Enable. Use following command to enable/disable RCOC for Busy Destination on all the mobile ports: 222-*-Code-#* SIMADO GFX44 V1 System Manual...
  • Page 108 Destination on Mobile Port is Enable. Use following command to enable/disable RCOC When Speech with Destination on all the mobile ports: 224-*-Code-#* Step 5 Use the following command to clear RCOC table entries: 225-#* SIMADO GFX44 V1 System Manual...
  • Page 109 • After placing the call on the basis of this logic, the corresponding entry is deleted from the database. • The entries in the database follow FIFO logic. Relevant Topics: 1. Mobile Port Parameters 2. Routing Type 116 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 110: Routing Group

    How it works? • Maximum 4 routing groups can be formed. • Maximum 4 members can be programmed in each routing group. • Each port (FXS, Mobile) is assigned different routing groups for SIMADO GFX44 V1 System Manual...
  • Page 111 Use following command to program a routing group: 201-Routing Group-Member Index-Port Type-Port Number-#* Where, Routing Group is from 1 to 4. Member Index is from 1 to 4. Port Type Meaning Port Number Null Mobile Default routing group table is given below: SIMADO GFX44 V1 System Manual...
  • Page 112 Routing Group is from 1 to 4. By default, Routing Group 4 is assigned to all the FXS ports. Use following command to assign a routing group to all the FXS ports for Timezone 1: 203-*-Routing Group-#* SIMADO GFX44 V1 System Manual...
  • Page 113 Use following command to assign a routing group to all the FXS ports for Timezone 4: 206-*-Routing Group-#* Step 5 Use following command to assign a routing group to a Mobile Port for Timezone 1: SIMADO GFX44 V1 System Manual...
  • Page 114 Use following command to assign a routing group to all the mobile ports for Timezone 3: 209-*-Routing Group-#* Use following command to assign a routing group to a mobile port for Timezone 4: 210-Mobile Port-Routing Group-#* Where, Mobile Port is from 1 to 4. SIMADO GFX44 V1 System Manual...
  • Page 115 Routing Group 01, then last 2 FXS ports get disabled and call is not routed on them. The disabled ports are indicated on LED’s. Relevant Topics: 1. Routing Type 116 2. Fixed Dialing 3. Time Table =X=X= SIMADO GFX44 V1 System Manual...

  • Page 116: Routing Type

    Matrix Routing Type What’s this? • The SIMADO GFX44 provides facility to select option for routing a call, originating on a Source Port. This is called ‘Routing Type’. The call originates on FXS port when it goes OFF-Hook but for mobile port, the call is originated when it receives an incoming call.
  • Page 117 Mobile port as the network cannot process the call with blank string. Like wise different source port will route the call as per the destination port programmed by the routing group. For emergency number, refer call flow diagram. The processing by the system is SIMADO GFX44 V1 System Manual...
  • Page 118 ON-Hook in case the source port is FXS port. But, if the source port is Mobile port, user gets disconnected only after expiry of busy/error tone timer. How it works? The call flow for GFX44 is explained below: SIMADO GFX44 V1 System Manual...
  • Page 119 TZ Digits dialed till FDWT? First Free Rotation System will wait for end of dialing digit/Inter digit timer Any Dest. port free? Call is placed on free Call is not answered port SIMADO GFX44 V1 System Manual...
  • Page 120 Call is placed the desintation port First Free Rotation Any Dest. port free? Call is not placed on ANT is applied, if applicable destination port Call is placed on destination port SIMADO GFX44 V1 System Manual...
  • Page 121 First Free Rotation Any Dest. port free? Call is not placed on destination port ANT is applied, if applicable Call is placed on the desintation port SIMADO GFX44 V1 System Manual...
  • Page 122 Call is placed on the desintation port Rotation First Free Any Dest. port free? Call is not placed on destination port ANT is applied, if applicable Call is placed on the desintation port SIMADO GFX44 V1 System Manual...
  • Page 123 • Call originates on FXS port when it goes OFF-Hook. • Call originates on Mobile port when it receives an incoming ring, and checks for RCOC logic. For more details on this refer chapter RCOC. SIMADO GFX44 V1 System Manual...
  • Page 124 Use following command to assign routing type for time zone 1 to a FXS port: 181-FXS Port-Routing Type-#* Where, FXS Port is from 1 to 4. Routing Type Meaning Answer-Number Based Routing Answer-Fixed Routing Direct Routing By default, Routing Type to a FXS Port is 1. SIMADO GFX44 V1 System Manual...
  • Page 125 Answer-Number Based Routing Answer-Fixed Routing Direct Routing By default, Routing Type to a FXS Port is 1. Use following command to assign routing type for time zone 3 for all the FXS ports: 183-*-Routing Type-#* SIMADO GFX44 V1 System Manual...
  • Page 126 By default, Routing Type to a Mobile Port is 3. Use following command to assign routing type for time zone 1 for all the mobile ports: 185-*-Routing Type-#* Use following command to assign routing type for time zone 2 to a mobile port: SIMADO GFX44 V1 System Manual...
  • Page 127 Use following command to assign routing type for time zone 3 for all the mobile ports: 187-*-Routing Type-#* Use following command to assign routing type for time zone 4 to a mobile port: 188-Mobile Port-Routing Type-#* Where, SIMADO GFX44 V1 System Manual...
  • Page 128 • Call originates on FXS port when it goes OFF-Hook and on Mobile port, when it receives incoming call. • Destination port is decided by the Routing Type, selected. Relevant Topics: 1. Routing Group 2. Time Table =X=X= SIMADO GFX44 V1 System Manual...

  • Page 129: Signal Strength

    Matrix Signal Strength What’s this? • The SIMADO GFX44 gives the indication of signal strength available for communication on SLT. Thus the possibility of network availability can be found. This information is important when user is dialing a number/receiving a call.

  • Page 130: Sim Pin

    SIM PIN variable of the system. The old SIM PIN number is already there with the system as config variable. Hence the user is not required to remember old SIMADO GFX44 V1 System Manual...
  • Page 131 Service Provider. Use following command to change the SIM PIN of a mobile port: 243-Mobile Port-New SIM PIN-#* Where, Mobile Port is from 1 to 4. New SIM PIN is from 8 digits maximum. SIMADO GFX44 V1 System Manual...
  • Page 132 • By default the SIM PIN for all the Mobile ports is ‘1234’ and this PIN number does not get default when the user gives the command to default the SIMADO GFX44 parameters. PIN values get default to 1234, only when the Version or Revision number of the software of the SIMADO GFX44 is changed.

  • Page 133: Software Version/Revision

    Software Version/Revision page will be opened. User can read the details of the software. • The other way is to open the page ‘SIMADO GFX44 Version Revision’ from the Main Menu and then click on ‘Display’ to know the details of the software. For example, the display can be as ‘V1R2’.

  • Page 134: Time Table

    2. • These examples highlight the need for the system to behave differently depending on the time of the day. The SIMADO GFX44 offers a very flexible programming for different time zones. A day can be divided in, four timezones. Such a schedule of a day is called a Time Table.
  • Page 135 Mobile Port is from 1 to 4. Time Table is from 1 to 4. By default, Time Table 1 is assigned to all the Mobile Ports. Use the following command to assign time tables to all the mobile ports: 333-Time Table-#* SIMADO GFX44 V1 System Manual...
  • Page 136 (Time Table Number 2) 332-1-2-#* (Assign Time Table 2 to FXS1) 181-1-1-#* (Routing Type: Answer-Number Based for TZ1) 182-1-0-#* (Routing Type: OFF for Timezone 2) Relevant Topics: 1. Routing Type 2. Routing Group 3. Default the Configuration =X=X= SIMADO GFX44 V1 System Manual...

  • Page 137: Section 3: Appendices

    Section 3: Appendices...

  • Page 139: Appendix A: Applications

    Matrix Appendix A: Applications The SIMADO GFX44 can be deployed for different application to interface with PSTN network, GSM network or PBX. Various application are explained with following cases: • Standalone with phones are connected and 4-SIM card inserted. • Connecting PBX at FXS ports.
  • Page 140 Matrix Application 2: SIMADO GFX44 with PBX Department 1 FXS 1 Phone 3 FXS 2 Phone 4 FXS 3 Phone 5 FXS 4 Phone 6 FXS 4 FXO 01 SIMADO Department 2 FXO 02 FXS 3 GFX44 FXO 03 CO Line 03...

  • Page 141: Appendix B: Technical Specifications

    ITU-T Q.23 and Q.24 Reception CLIP DTMF, FSK ITU-T V.23 and FSK Bellcore 202 Flash Timer 83-999msec. (Programmable) Answer Signaling on FXS None, Polarity (Battery) Reversal Disconnect Signaling on None, Polarity (Battery) Reversal, Open Loop Disconnect SIMADO GFX44 V1 System Manual...
  • Page 142 : 5-95% RH, Non-Condensing Storage Humidity : Max. 95% Non Condensing at 40°C (104°C) Packaging: Dimensions (WxHxD) 155 x 220 x 50 mm (6.10" x 8.66" x 1.97") Unit Weight 1.00Kg (2.20lbs) Approx. Installation Wall Mountable, Desk-Top =X=X= SIMADO GFX44 V1 System Manual...

  • Page 143: Appendix C: System Commands

    To ena/dis the filter for calls ter. on FXS 141-Code-#* To print all calls to terminated on Mobile 133-Mobile Port-Mobile Port-#* To ena/dis the filter for calls ter. on Mobile 142-Code-#* To print all calls to originated on FXS 134-FXS Port-FXS Port-#* SIMADO GFX44 V1 System Manual...
  • Page 144 To program the emergency no. in table 233-Index-Emeregency Number-#* To clear the emergency no. at an index 233-Index-#* To assign routing group for an index 234-Index-Routing Group-#* Fixed Dialing To ena./dis. fixed dialing on a FXS port 171-FXS Port-Code-#* SIMADO GFX44 V1 System Manual...
  • Page 145 To program n/w selection mode for Mobile 231-Mobile Port-Mode-#* To program n/w sele. mode for all Mobiles 231-*-Mode-#* To program n/w operator no. with priority 232-Mobile Port-Priority-Code-#* To clear network operator number 232-Mobile Port-Priority-#* To read network operator code for mobile By Jeeves SIMADO GFX44 V1 System Manual...
  • Page 146 To assign a RG to a Mobile port for TZ4 210-Mobile Port-Routing Group-#* To assign a RG to all Mobile ports for TZ4 210-*-Routing Group-#* Routing Type To assign routing type for TZ1 for FXS 181-FXS Port-Routing Type-#* SIMADO GFX44 V1 System Manual...
  • Page 147 To assign time table to FXS port 332-FXS Port-Time Table-#* To assign time table to all FXS ports 332-*-Time Table-#* To assign time table to Mobile port 333-Mobile Port-Time Table-#* To assign time table to all Mobile ports 333-*-Time Table-#* =X=X= SIMADO GFX44 V1 System Manual...

  • Page 148: Appendix D: Regulatory Information

    Matrix Appendix D: Regulatory Information SIMADO GFX44 V1 System Manual...
  • Page 149 Matrix SIMADO GFX44 V1 System Manual...

  • Page 150: Index

    Enable/Disable Allowed/Denied List-See Allowed and Denied Lists Enable/Disable Automatic Number Translation-See Automatic Number Translation 37 Feature Tone-See Call Progress Tone Generation 49 Filter Settings-See Call Detail Recording (CDR) 41 First Digit Wait Timer-See FXS Port Parameters Fixed Destination Number-See Fixed Dialing SIMADO GFX44 V1 System Manual...
  • Page 151 Network Response Timer-See Mobile Port Parameters No Response Destination-See RCOC 104 Open Loop Disconnect Timer-See Disconnect Signaling on FXS Port 64 Personal Unlock Keyword (PUK)-See SIM PIN Polarity Reversal-See Answer Signaling on FXS Port 32 SIMADO GFX44 V1 System Manual...
  • Page 152 Silence-See Call Proceeding Tone 47 Substitute Number List-See Automatic Number Translation Source Port-See Call Detail Recording (CDR) 41 Time Zone-See Routing Type, Time Table 116, 134 Tx Gain-See FXS Port Parameters, Mobile Port Parameters 75, 86 =X=X= SIMADO GFX44 V1 System Manual...

  • Page 153: Notes

    Matrix Notes SIMADO GFX44 V1 System Manual...
  • Page 154 Matrix Notes SIMADO GFX44 V1 System Manual...

  • Page 155: Programming Register

    Matrix Programming Register S.N. Date Major Programming Changes made SIMADO GFX44 V1 System Manual...
  • Page 156 Matrix Programming Register S.N. Date Major Programming Changes made SIMADO GFX44 V1 System Manual...

Table of Contents