Index Of Commands - Stanford Research Systems DS360 Operating Manual And Programming Reference

Index of Commands

Variables
i, j, k, n
x
Function Output Control Commands
FUNC (?) i
FREQ (?) x
AMPL (?) x
OFFS (?) x
OUTE (?) i
OUTM (?) i
TERM (?) i
RELA (?) i
STPE (?) i
FSTP (?) x
TTAA (?) x
TTBA (?) x
TTAF (?) x
TTBF (?) x
TTMD (?) i
Digital Output Control Commands
FUNC (?) i
DFRQ (?) x
DAMP (?) x
OUTD (?) i
DIGM (?) i
DIGF (?) i
STPE (?) i
FSTP (?) x
DTAA (?) x
DTBA (?) x
DTAF (?) x
DTBF (?) x
DIGB (?) i
Modify Function Commands
*TRG 4-14
MENA (?) i 4-14
MTYP (?) i 4-14
TSRC (?) i 4-14
STFR (?) x 4-14
SPFR (?) x 4-14
RATE (?) x 4-14
BCNT (?) x 4-15
RCNT (?) i 4-15
integers
real numbers
4-9 0=sin, 1=sqr, 2=wht noise, 3=pink noise, 4=2Tone.
4-9 Sets Output Freq to x.
4-9 Sets Ampl to x; must include VP, VR, dB, dV or dm.
4-9 Sets Output Offset to x.
4-9 Output Enable (i=1), Disable (i=0).
4-9 Output Mode 0=unbal, 1=bal.
4-10
Source Impedance 0=50Ω, 1=150Ω, 2=600Ω, 3=HiZ.
4-10 Sets Relative Amplitude Mode ON (i=1) or OFF (i=0).
4-10 Freq Step Enable (i=1) Disable (i=0).
4-10 Sets Freq Step to x.
4-10 Sets Tone A amp to x; must include VP, VR, dB, dV or dm.
4-11 Sets Tone B amp to x; must include VP, VR, dB, dV or dm.
4-11 Sets Tone A frequency to x.
4-11 Sets Tone B frequency to x.
4-11 Sets 2-Tone Mode to sine (i=0) or square (i=1).
4-12 0=sin, 4=2Tone (1, 2, 3 not allowed in digital mode).
4-12 Sets Digital Output Freq to x.
4-12 Sets Digital Ampl to x (in %).
4-12 Digital Output Enabled (i=1) or Disabled (i=0).
4-12 Digital Output Mode 0=Professional, 1=Consumer.
4-12 Digital Sampling Frequency 0=48 kHz, 1=44.1 kHz, 2=32 kHz.
4-13 Freq Step Enable (i=1) Disable (i=0).
4-13 Sets Freq Step to x.
4-13 Sets Digital Tone A amp to x (in %).
4-13 Sets Digital Tone B amp to x (in %).
4-13 Sets Digital Tone A frequency to x.
4-13 Sets Digital Tone B frequency to x.
Sets Digital Number of Bits (16 ≤ i ≤ 20).
4-13
Triggers a single sweep or burst.
Modify Function Enable (i=1) or Disable (i=0).
Sets the modify function type to Lin Swp, Log Swp, Burst, BWNoise
for i=0,1,2,3.
Sets the trigger source to Int, Ext, Single or Gate for i=0,1,2,3.
Sets Sweep Start Frequency to x.
Sets Sweep Stop Frequency to x.
Sets Sweep Rate to x.
Sets Burst Count to x (i=.5, 1-65534).
Sets Burst Rate to x (i=1-65535).
Remote Programming
DS360 Ultra Low Distortion Function Generator
4-3