Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Phoenix Model super constellation
Summary of Contents for Phoenix Model super constellation
- Page 1 I n s t r u c t i o n M a n u a l I n s t r u c t i o n M n s t r u c t i o n M a n u u c t i o n M a n u a l o n M a n u Wingspan : 4300mm (169.3 inches)
-
Page 2: Kit Contents
Instruction Manual SUPER CONSTELLATION KIT CONTENTS: We have organized the parts as they come out of the box for better identification during assembly. We recommend that you regroup the parts in the same manner. This will ensure you have all of parts required before you begin assembly. -
Page 3: Tools And Supplies Needed
1. Please trial fit all the parts. Make sure you have the correct parts and that they fit and are aligned properly before gluing! This will assure proper assembly. The Super Constellation is hand made from natural materials, every plane is unique and minor adjustments may have to be made. -
Page 4: Installing The Control Horns
Instruction Manual SUPER CONSTELLATION 4. Using the thread as a guide and using masking INSTALLING THE CONTROL HORNS tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you 1. The aileron has a block wood plate for mounting have pulled the servo lead out, remove the the control horn. -
Page 5: Installing The Aileron Linkages
Instruction Manual SUPER CONSTELLATION 3. Repeat step # 1 - # 2 to install the second control horn on the aileron. ↑ To the cowl Screw Flat washer ↑ Aluminum link ball To the cowl Plastic link ball Servo arm... -
Page 6: Installing The Landing Gear
Instruction Manual SUPER CONSTELLATION INSTALLING THE flap 3. Install the air tube. Repeat these step from installing the aileron for installing the flap. 22mm 22mm 130mm 22mm 22mm 140mm 4. Pull out the air tube through the wing section. 5. Secure the air retract to the wing. - Page 7 Instruction Manual SUPER CONSTELLATION 6. Lock the window using C.A glue. 2. Attach and secure the wheel to the nose gear. C.A Glue 7. Slide and secure two cable rod to the nose gear. 3. Install and secure the nose gear Metal lock 8.
-
Page 8: Installing The Elevator Servo
Instruction Manual SUPER CONSTELLATION 10. Install the retract servo. Remove the covering Metal connector 11. Finish the nose air retract. Servo lead INSTALLING THE ELEVATOR servo 1. Remove the covering from over the precut servo box on the elecator. 2. Install two servo to the elevator as shown. -
Page 9: Installing The Rudder Servo
Instruction Manual SUPER CONSTELLATION INSTALLING THE elevator linkages 1. The elevator linkages are assembled as shown below. 22mm 22mm 60mm 2. Repeat these step as installing the aileron linkages Remove the covering INSTALLING THE RUDDER SERVO Repeat step 1 - step 6 from the ailleron to the rudder... -
Page 10: Installing The Horizontal Stabilizer
Instruction Manual SUPER CONSTELLATION Machine screw Servo lead Machine screw INSTALLING THE HORIZONTAL STABILIZER 1. Remove the covering from the fuselage. Remove the covering... -
Page 11: Installing The Engine
Instruction Manual SUPER CONSTELLATION Servo lead 2. Secure the vertical stabilizer. INSTALLING THE ENGINE 3. Attach the stabilizer to the fuselage. This manual, we used the GT 33 OS 165mm 4. Secure the elevator stabilizer. Machine screw... -
Page 12: Installing The Stopper Assembly
Instruction Manual SUPER CONSTELLATION Do not secure the tank into place permanently INSTALLING THE STOPPER ASSEMBLY until after balancing the airplane. You may need to remove the tank to mount the battery in the 1. The stopper has been pre-assembled at the factory. -
Page 13: Installing The Control Air System
Instruction Manual SUPER CONSTELLATION 3. While holding the cowl firmly in position, drill four 1,6mm pilot holes through both the cowl and the side edges of the firewall. 4. Using a 3mm drill bit, enlarge the four holes in the cowling. - Page 14 Instruction Manual SUPER CONSTELLATION 2. The air valve. Screw Screw Screw Screw Screw Screw 3. Attach the air valve to the servo. Wing screw Zip tie Carbon Carbon Aluminum tube tube tube Metal connector 4. Attach the fuselage to the fuselage.
- Page 15 Instruction Manual SUPER CONSTELLATION 3. Drill through the mark you make with a 2.5mm drill bit (Note: just through the wing joiner). Bomb Machine screw 4. Secure the wing joiner using a 4mm x 35mm wood screw. C.A glue BALANCING 1.
-
Page 16: Lateral Balance
Instruction Manual SUPER CONSTELLATION Low rate: Aileron 25mm up 25mm down 210mm Elevator 25mm up 25mm down Rudder 40mm right 40mm left 25mm 25mm Aileron Control LATERAL BALANCE After you have balanced a plane on the C.G. 25mm You should laterally balance it. Doing this will 25mm help the airplane track straighter. - Page 17 Instruction Manual SUPER CONSTELLATION I/C FLIGHT WARNINGS Always operate in open areas, away Keep all onlookers (especially small THE PROPELLER IS DANGEROUS from factories, hospitals, schools, children and animals) well back from buildings and houses etc. NEVER fly Keep fingers, clothing (ties, shirt the area of operation.
- Page 18 Instruction Manual SUPER CONSTELLATION I/C FLIGHT GUIDELINES Operate the control sticks on the When ready to fly, first extend the transmitter and check that the control transmitter aerial. surfaces move freely and in the ALWAYS land the model INTO the CORRECT directions.
Need help?
Do you have a question about the super constellation and is the answer not in the manual?
Questions and answers