Related Manuals for Taylor C819
Summary of Contents for Taylor C819
- Page 1 Models C819 & C821 Auto Lift Grills Original Operating Instructions 073946-M 5/10/11 (Original Publication) (Updated 10/14/11)
- Page 2 Amps Part Number: E May, 2011 Taylor All rights reserved. 073946-M Taylor Company The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.
-
Page 3: Table Of Contents
........Table of Contents Models C819 & C821... - Page 4 E May, 2011 Taylor (Original Publication) (Updated October, 2011) All rights reserved. 073946-M Taylor Company The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.
-
Page 5: To The Installer
The grill is supplied with one power cord. Check the service of Taylor equipment. data plate on the grill for voltage, cycle, phase and electrical specifications. Only Taylor authorized service personnel should perform installation and repairs on For proper power connections, refer to the wiring the equipment. -
Page 6: Installation
NSF Standard 4 requirements. To the Installer Models C819 & C821... -
Page 7: To The Operator
Note: Warranty is valid only if the parts are authorized Taylor parts, purchased from an authorized Taylor Distributor, and the required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on equipment or parts if... -
Page 8: Safety
Taylor has gone other device to disconnect the appliance to extreme efforts to design and manufacture built-in... - Page 9 NOTICE all warning labels that have been liquid collecting inside the grill and attached to the grill to further point out safety destroying electrical components precautions to the operator. Models C819 & C821 Safety...
- Page 10 For additional information regarding applicable local adapting the appliance to the utilization conditions of laws, please contact the municipal facility and/or that country. local distributor. Safety Models C819 & C821...
-
Page 11: Operator Parts Identification
SWITCH-ROCKER-DPST-10A 076989-WP PANEL A.-BACK SERVICE X69664 PLUG A.-USB CABLE 073808 DEFLECTOR A.-FLUE X69657 BUTTON-OPERATOR-BLACK 076012 SCREW-3/8-16X1-1/2 SERR 020129 BUTTON-OPERATOR-RED 076011 KIT A.-GREASE SHIELD X78330-SER PANEL A.-LIGHT X69678 PANEL-SIDE UPPER-RIGHT 073989 PANEL-SIDE-LOWER-RIGHT 073991 110902 Models C819 & C821 Operator Parts Identification... -
Page 12: C821
SWITCH-ROCKER-DPST-10A 076989-WP PANEL A.-BACK SERVICE X69664 PLUG A.-USB CABLE 073808 DEFLECTOR A.-FLUE X69657 BUTTON-OPERATOR-BLACK 076012 SCREW-3/8-16X1-1/2 SERR 020129 BUTTON-OPERATOR-RED 076011 KIT A.-GREASE SHIELD X78330-SER PANEL A.-LIGHT X69678 PANEL-SIDE UPPER-RIGHT 073989 PANEL-SIDE-LOWER-RIGHT 073991 110902 Operator Parts Identification Models C819 & C821... -
Page 13: Accessories
072673 ***7 HOLDER-CLEANING 073736 W/TAB ***8 PAD-CLEANING 073737 SCRAPER-TEFLON WIPER 075887 SHOWN PER PLATEN ** SHOWN PER PLATEN (NOTE: EXTRA CLIPS ARE SENT WITH GRILL) *** SOLD SEPARATELY THROUGH YOUR LOCAL DISTRIBUTOR 110602 Models C819 & C821 Operator Parts Identification... -
Page 14: Important: To The Operator
Important: To the Operator Figure 4 ITEM DESCRIPTION ITEM DESCRIPTION RAISE BUTTON PROGRAM KEY STANDBY/COOK MODE BUTTON TEMPERATURE INDICATOR LIGHTS MASTER POWER SWITCH POWER KEY COVER A.-USB FUNCTION DISPLAY CLEAN MODE KEY MENU SELECT KEYS Important: To the Operator Models C819 & C821... -
Page 15: Operating Procedures
Section 6 Operating Procedures The Models C819 and C821 are 24” (610 mm) grills. Step 1 The C819 is equipped with two independent 12” Slide the release sheet retainer through the hemmed (305 mm) upper platens and the Model C821 is end of the release material sheet. - Page 16 Place the release material clips over the release platen. material sheet. Press them into place over the release material bar at the top of the platen. Note: Temperature checks should only be conducted with the release material sheets removed. Figure 8 Operating Procedures Models C819 & C821...
- Page 17 DO clean daily on both sides, using an release material are very hot. To prevent burn approved high temperature grill cleaner and injuries, wear heat-resistant gloves when the grill cleaning pad and holder identified on replacing release material. page 9. 110602 Models C819 & C821 Operating Procedures...
- Page 18 Figure 13 Figure 12 The control will display the word “INITIALIZATION” Note: Contact your local Taylor Distributor to for five seconds and then enter the OFF mode. The purchase the grill cleaning pad and holder. control will now display the word “OFF”. The (See page 9.)
- Page 19 When the grill is at the proper temperature, the temperature statements will no longer display and the temperature indicators will be illuminated in green. Figure 15 Figure 17 Figure 16 Models C819 & C821 Operating Procedures...
- Page 20 The PASSWORD screen will appear. Enter the The ADJUST VOLUME key displays the current following password: STORE1. Press the OK key. volume. To increase or decrease the volume, use the UP and DOWN arrow keys. Figure 19 Figure 21 Operating Procedures Models C819 & C821...
- Page 21 GAP: This key is only active if CLAM has been selected. The key displays the platen gap (in inches or mm) associated with the FUNCTION. To increase or decrease the gap setting, use the UP and DOWN Figure 23 arrow keys. Models C819 & C821 Operating Procedures...
-
Page 22: Loading Store Menu Items To Usb
SERVICE CONTACT INFORMATION Key Figure 26 Step 4 Press the SERVICE CONTACT INFORMATION key Enter the Operator Password “STORE1” and press to view the programmed service contact information. the OK key. Figure 25 Figure 27 110603 Operating Procedures Models C819 & C821... -
Page 23: Loading Menu Items From Usb
Remove the USB flash drive from the USB port and reinstall the USB cable cap on the USB connector. Note: Grills built prior to serial number M1035495 will require the front control panel be reinstalled. 110603 Models C819 & C821 Operating Procedures... - Page 24 Patties are generally placed two at a time from front to back of grill and right to left. The removal order of the patties is shown in the diagram by the number shown in the center of each patty. Operating Procedures Models C819 & C821...
- Page 25 RAISE button. A tone will sound and the display will The display reads “MOVING DOWN” as the platen read “CANCEL” for five seconds and then enter an lowers to the cook surface. IDLE mode. Models C819 & C821 Operating Procedures...
- Page 26 Figure 34 CAUTION: Never use force to raise the upper platen. Damage to components may result. Only use the RAISE button to open the upper platen! Figure 36 Operating Procedures Models C819 & C821...
-
Page 27: Daily Cleaning Procedures
Note: To increase the life of the release material sheet, wipe it with a clean, sanitizer-soaked, folded result. Only use the RAISE button to open the grill cloth a minimum of four times every hour. upper platen! Models C819 & C821 Operating Procedures... - Page 28 Step 3 Step 5 Press the RAISE button to cancel the alarm. Wipe the exposed surface of the release material sheets with a clean, sanitizer-soaked grill cloth. Figure 40 Figure 42 Operating Procedures Models C819 & C821...
- Page 29 DO NOT fold, crease, or place them on sharp objects. Figure 46 Step 12 Remove, empty, and reinstall the grease cans. Figure 44 Figure 47 Models C819 & C821 Operating Procedures...
- Page 30 Press the STANDBY button to lower one of the platens. Step 21 Apply grill cleaner to the inner edges of the platens. Step 22 Figure 49 Press the RAISE button to raise the lowered platen. 110602 Operating Procedures Models C819 & C821...
- Page 31 Starting at the back of the lower grill, spread the remaining grill cleaner over the entire surface. Do Step 29 Press the RAISE button to raise the lowered platen. not scrub while applying product. 110602 Models C819 & C821 Operating Procedures...
- Page 32 Failure to follow these instructions may result in: serious electrical shock burns from hot steam liquid collecting inside the grill and destroying electrical components damaged cook surfaces Figure 58 110602 Operating Procedures Models C819 & C821...
- Page 33 9, ONLY. Using any other pad Step 44 and holder will damage the release material sheets. Remove and empty the grease cans. Note: Contact your local Taylor Distributor to purchase the correct grill cleaning pad and holder. (See page 9.) Step 40 Place the release material sheets flat on the lower grill surface.
- Page 34 Step 50 Place the power switch in the OFF position. Step 47 Wipe all exterior panels. Step 48 Apply a light coat of vegetable oil to the entire lower grill surface. Figure 63 Figure 64 Operating Procedures Models C819 & C821...
-
Page 35: Section 7 Troubleshooting Guide
Press the STANDBY button within five seconds of lowering in the STANDBY mode, but will button. the platen into the COOK stay in the COOK position. position. b. Faulty wire connections. b. Call a service technician. Models C819 & C821 Troubleshooting Guide... - Page 36 Call a service technician. preset gap height. b. Defective motor interface b. Call a service technician. board. c. Loose harness connections. c. Call a service technician. d. Defective main display d. Call a service technician. controller. Troubleshooting Guide Models C819 & C821...
- Page 37 Call a service technician. SWITCH STUCK ON.” b. Defective stepper motor. b. Call a service technician. c. Defective stepper motor wire c. Call a service technician. harness. d. Defective Home switch. d. Call a service technician. Models C819 & C821 Troubleshooting Guide...
- Page 38 The grill is out of calibration. a. Call a service technician. is cool or overheats. b. The processor control is faulty. b. Call a service technician. c. The thermocouple is faulty. c. Call a service technician. Troubleshooting Guide Models C819 & C821...
-
Page 39: Section 8 Parts List
Section 8 Parts List + Available Separately 111014 Models C819 & C821 Parts List... - Page 40 + Available Separately Parts List Models C819 & C821...
- Page 41 + Available Separately Models C819 & C821 Parts List...
- Page 42 + Available Separately Parts List Models C819 & C821...
- Page 43 + Available Separately Models C819 & C821 Parts List...
- Page 44 + Available Separately Parts List Models C819 & C821...
- Page 45 + Available Separately Models C819 & C821 Parts List...
- Page 46 + Available Separately Parts List Models C819 & C821...
- Page 47 + Available Separately Models C819 & C821 Parts List...
- Page 48 C819 073814-23 9/11...
- Page 49 C821 069842-23 9/11...