Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual page 81

Specifications
Max. terminal load (AC-1)
Max. terminal load (AC-15)
Max. terminal load (DC-1)
Max. terminal load (DC-13)
Min. terminal load on 1-3 (NC), 1-2 (NO), 4-6 (NC), 4-5 (NO)
Environment according to EN 60664-1
1) IEC 60947 parts 4 and 5
The relay contacts are galvanically isolated from the rest of the circuit by reinforced isolation (PELV).
2) Overvoltage Category II
3) UL applications 300V AC 2A
Control card, 10 V DC output:
Terminal number
Output voltage
Max. load
The 10V DC supply is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals.
Control characteristics:
Resolution of output frequency at 0 - 1000Hz
System response time (terminals 18, 19, 27, 29, 32, 33)
Speed control range (open loop)
Speed accuracy (open loop)
All control characteristics are based on a 4-pole asynchronous motor
Surroundings:
Enclosure type A
Enclosure type B1/B2
Enclosure type B3/B4
Enclosure type C1/C2
Enclosure type C3/C4
10 10
Enclosure type D1/D2/E1
Enclosure type D3/D4/E2
Enclosure kit available ≤ enclosure type A
Vibration test enclosure A/B/C
Vibration test enclosure D/E/F
Max. relative humidity
Aggressive environment (IEC 721-3-3), uncoated
Aggressive environment (IEC 721-3-3), coated
Test method according to IEC 60068-2-43 H2S (10 days)
Ambient temperature
Derating for high ambient temperature, see section on special conditions
Minimum ambient temperature during full-scale operation
Minimum ambient temperature at reduced performance
Temperature during storage/transport
Maximum altitude above sea level without derating
Maximum altitude above sea level with derating
Derating for high altitude, see section on special conditions
EMC standards, Emission
EMC standards, Immunity
See section on special conditions
Control card performance:
Scan interval
Control card, USB serial communication:
USB standard
USB plug
78
®
VLT AQUA Drive
Operating Instructions
1)
on 4-6 (NC) (Resistive load)
on 4-6 (NC) (Inductive load @ cosφ 0.4)
1)
1) on 4-6 (NC) (Resistive load)
1)
on 4-6 (NC) (Inductive load)
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6
MG.20.M8.02 - VLT
overvoltage category III/pollution degree 2
30 - 4000 rpm: Maximum error of ±8 rpm
IP20/Chassis, IP21kit/Type 1, IP55/Type12, IP66
5% - 95%(IEC 721-3-3; Class 3K3 (non-condensing) during operation
EN 61800-3, EN 61000-6-3/4, EN 55011, IEC 61800-3
®
is a registered Danfoss trademark
240V AC, 2 A
240V AC, 0.2A
50V DC, 2 A
24V DC, 0.1 A
24V DC 10mA, 24V AC 20mA
50
10.5V±0.5V
25mA
: +/- 0.003Hz
: ≤ 2ms
1:100 of synchronous speed
IP21/Type 1, IP55/Type12, IP66
IP20/Chassis
IP21/Type 1, IP55/Type 12, IP66
IP20/Chassis
IP21/Type 1, IP54/Type12
IP00/Chassis
IP21/TYPE 1/IP4X top
1.0g
0.7g
class 3C2
class 3C3
Max. 50°C
0°C
- 10 °C
-25 - +65/70°C
1000m
3000m
EN 61800-3, EN 61000-6-1/2,
: 5ms
1.1 (Full speed)
USB type B "device" plug