Panasonic AJ-HPM100P Operating Instructions Manual page 118

Item
FR SUPER
No. DISP.
504 RUN MODE
505 TCG REGEN
507 EXT TC SEL
508 BINARY GP
509 PHASE CORR
510 TCG CF FLAG
511 DF MODE
512 TC OUT REF
513 VITC OUT
514 HD EMBD VITC
118
Setup: Item Settings
Setting
FR SUPER
No. DISP.
0000 REC Specifies an operating mode that advances the internal time code generator.
0: The internal time code generator is advanced only during recording.
0001 FREE
1: When the power is on, the internal time code generator is advanced regardless of
operating mode.
0000 TC&UB Specifies the signal to regenerate when the time code generator (TCG) is in the REGEN
mode.
0001 TC
0: Regenerates both the time code and the user bit
0002 UB
1: Regenerates only the time code
2: Regenerates only the user bit
0001 EXT_L Specifies the time code used when an external time code is used.
0: LTC of the TIME CODE IN connector
0002 SLTC
1: LTC data attached to serial signal input to HD SDI IN
0003 SVITC
2: VITC data attached to serial signal input to HD SDI IN
NOTE:
When SLTC and SVITC are set, the VITC in the input video signal is used when an analog
composite or SD SDI input signal is selected. When 1394 is selected as the input signal,
the IEEE 1394 digital input signal time code is used regardless of this setting.
0000 000 Specifies user bit usage in time code generated by the TCG.
0: NOT SPECIFIED (character set not specified)
0001 001
1: ISO CHARACTER (8-bit character set complying with ISO646 and ISO2022)
0002 010
2: UNASSIGNED 1 (undefined)
0003 011
3: UNASSIGNED 2 (undefined)
0004 100
4: UNASSIGNED 3 (undefined)
0005 101
5: PAGE/LINE
0006 110
6: UNASSIGNED 4 (undefined)
0007 111
7: UNASSIGNED 5 (undefined)
0000 OFF
Specifies whether or not LTC output from the TIME CODE OUT connector should be phase
controlled.
0001 ON
0: No phase control
1: Phase controlled
0000 OFF
Sets the TCG CF flag.
0: OFF
0001 ON
1: ON
0000 DF Sets the DF or NDF mode for CTL and TCG.
0: Uses drop frame mode.
0001 NDF
1: Uses non-drop frame mode.
NOTE:
This menu is not displayed when 50 is selected in menu No. 25 SYSTEM FREQ.
0000 VOUT Specifies how the phase is switched for the time code output by the TIME CODE OUT
connector for the external LTC input when the TC INT/EXT switch is set to EXT. (only in EE
0001 TC_IN
mode)
0: Synchronized with output video signal.
1: Synchronized with the external time code input.
0000 SBC Specifies how to output VITC that will be superimposed on the SD output video signal.
0: Outputs the time code recorded in the SBC area as VITC
0001 VAUX
1: Outputs the time code recorded in the VAUX area as VITC
NOTE:
• VITC data detected in the input video signal is automatically recorded in the VAUX area
during video recording.
• When CMPST and SDI are selected as input signals, VITC, which is output during
recording, outputs a time code that is superimposed on the input signal regardless of
above settings.
0000 OFF Specifies whether or not VITC data will be superimposed on HD SDI output.
0001 ON
0: Not superimposed
1: Superimposed
Settings and brief function description