Precaution Statements; Safety Precautions - Sam4s ER-180U Series Operation And Programming Manual

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential
hazards such as electrical shock.
1-1

Safety Precautions

1. Be sure that all built-in protective devices are
replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies,
be sure to restore all protective devices, including
nonmetallic control knobs and compartment
covers.
3. Make sure there are no cabinet openings through
which people - particularly children - might insert
fingers and contact dangerous voltages.
Such openings include excessively wide cabinet
ventilation slots and improperly fitted covers and
drawers.
4. Design Alteration Warning:
Never alter or add to the mechanical or electrical
design of the ECR. Unauthorized alterations might
create a safety hazard. Also, any design changes
or additions will void the manufacturer s warranty.
5. Components, parts and wiring that appear to have
overheated or that are otherwise damaged should
be replaced with parts that meet the original
specifications. Always determine the cause of
damage or over- heating, and correct any
potential hazards.
CAUTION
There is the danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose used batteries according to the instructions.
SAFETY NOTICE:

Precaution Statements

" F o r p l u g g a b l e e q u i p m e n t , t h e s o c k e t - - - - o u t l e t " F o r p l u g g a b l e e q u i p m e n t , t h e s o c k e t
" F o r p l u g g a b l e e q u i p m e n t , t h e s o c k e t " F o r p l u g g a b l e e q u i p m e n t , t h e s o c k e t
t h e e q u i p m e n t a n d s h a l l b e e a s i l y a c c e s s i b l e . " t h e e q u i p m e n t a n d s h a l l b e e a s i l y a c c e s s i b l e . " t h e e q u i p m e n t a n d s h a l l b e e a s i l y a c c e s s i b l e . " t h e e q u i p m e n t a n d s h a l l b e e a s i l y a c c e s s i b l e . "
6. Observe the original lead dress, especially near the
following areas: sharp edges, and especially the
AC and high voltage supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do not
change the spacing between components and the
printed circuit board. Check the AC power cord for
damage. Make sure that leads and components
do not touch thermally hot parts.
7. Product Safety Notice:
Some electrical and mechanical parts have special
safety-related characteristics that might not be
obvious from visual inspection. These safety
features and the protection they give might be lost
if the replacement component differs from the
original - even if the replacement is rated for
higher voltage, wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading, (
or ( ). Use replacement components that have
the same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the same
safety characteristics as the original might create
shock, fire or other hazards.
ATTENTION
ll y a danger d explosion s il y a remplacement incorrect
de la batterie.
Remplacer uniquement avec une batterie du même type
ou d un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant
o u t l e t s h o u l d s h o u l d b e i n s t a l b e i n s t a l l e d n e a r
o u t l e t o u t l e t s h o u l d s h o u l d b e i n s t a l b e i n s t a l
.
l e d n e a r
l e d n e a r l e d n e a r
)