Yeastar S50 Installation Guide Content Content………………………………………………………………………………………………………...2 Welcome……………………………………………………………………………………………………….3 Before You Start……………………………………………………………………………………………...4 Package Contents………………………………………………………………………………………….4 Hardware Overview………………………………………………………………………………………..4 LED Indicators and Ports………………………………………………………………………………….5 Installation…………………………………………………………………………………………………….7 Safety Disclaimers and Installation Warnings……………………………………………………………7 Module Installation………………………………………………………………………………………….7 Desktop Installation……………………………………………………………………………………….10 Rack Installation ………………………………………………………………………………………….10 Ground Connection………………………………………………………………………………………..11 Connecting the Equipment……………………………………………………………………………….12 Getting Started with the Configuration…………………………………………………………………13...
ISDN BRI, PSTN, and GSM connectivity, providing VoIP communications for up to 50 users. This guide describes how to install the S50 and how to log in the web GUI to configure the system. Once you complete the installation, refer to the Yeastar S-Series Administrator Guide for instructions on how to perform configurations on the system.
Yeastar S50 Installation Guide Before You Start Before you begin to install the S50 IP Phone System, please check the package contents to verify that you have received the items below. If there is any problem, please contact your provider.
Yeastar S50 Installation Guide LED Indicators and Ports LED Indicators Indication Status Description The power is switched on. POWER Power status The power is switched off. Blinking The system is running properly. System System status Static/Off The system goes wrong.
Page 6
Rotate the antenna into the Antenna Socket. SD Slot Insert a SD card. Yeastar S50 provides two 10/100/1000 Mbps adaptive RJ45 Ethernet ports. There are 3 Ethernet modes for the system. The default mode is “Single”. Single: LAN port interface will be used for uplink connection. WAN port is Ethernet Port disabled.
Before cleaning the device, cut off the power supply. Environment Install the Yeastar S50 IP PBX in a location that is clean, free from vibration, electric shock, and temperature/humidity extremes. The operating temperature should be kept below 104° F (40° C). Module Installation Yeastar S50 supports installing up to 4 modules.
Page 8
Yeastar S50 Installation Guide STEP 1 Loosen the screws on the enclosure and then remove the upper cover. STEP 2 Insert the module to the Module Slot. STEP 3 Insert a SIM card on the GSM/3G module following the instructions. Skip this step if no GSM/3G module installed.
Page 9
Yeastar S50 Installation Guide STEP 4 Close the cover and fix the screws. STEP 5 Rotate the antenna into the Antenna Socket. Skip this step if no GSM/3G module installed. 9/13...
Yeastar S50 Installation Guide Desktop Installation WARNING Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. STEP 1 Place the IP PBX on a steady platform. STEP 2 Remove the adhesive backing paper from the rubber feet.
Yeastar S50 Installation Guide STEP 2 Place the PBX in the 19-inch rack and fix both brackets to the rack with the rack’s proprietary mounting equipment. Ground Connection WARNING Proper grounding (connection to ground) is very important to reduce the risk to the user of electrocution or protect the PBX from the bad effects of external noise in the case of a lightning strike.
LAN switch/router. STEP 2 Plug the provided power cord into the power jack on S50 and the other end to a standard electrical wall socket. Wait for the system to boot up till the SYSTEM LED starts to blink.
Yeastar S50 Installation Guide Getting Started with the Configuration Yeastar S50 IP Phone System provides web-based configuration interface for administrator. The administrator can manage the device by logging in the Web interface. Access path: https://192.168.5.150:8088 User Name: admin ...