Self-Diagnosis Code Table - Sony DCR-PC100 Service Manual

4.

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0 0
C 2 1 0 0
C 2 2 0 0
C 3 1 1 0
C 3 1 1 1
C 3 1 2 0
C 3 1 2 1
C 3 1 2 2
C 3 1 2 3
C 3 1 2 4
C 3 1 3 0
C 3 1 4 0
C 3 1 4 2
C 3 1 1 0
C 3 1 1 1
C 3 2 2 0
C 3 2 2 1
C 3 2 2 2
C 3 2 2 3
C 3 2 2 4
C 3 2 3 0
C 3 2 4 0
C 3 2 4 2
E 6 1 0 0
E 6 1 1 0
E 6 2 0 0
E 6 2 0 1
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting the
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-
out.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
Winding S reel fault when counting the
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drum
operations
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus MR sensor (Pin wf,wg of CN171 of
CD-234 board) when focusing is performed when the control dial
is rotated in the focus manual mode, and the focus motor drive circuit
(IC401 of VC-227 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin 2,3 of CN171 of
CD-234 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC401 of VC-227 board)
when zooming is not performed.
Inspect pitch angular velocity sensor (SE451 of MA-367 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE450 of MA-367 board)
peripheral circuits.
— 8 —
Correction