Handycam vision digital video camera recorder (124 pages)
Summary of Contents for Sony DCR-PC100
Page 1
Australian Model Chinese Model DCR-PC100E E Model Hong Kong Model Ver 1.0 1999. 09 Tourist Model Photo : DCR-PC100 DCR-PC100/PC100E D300 MECHANISM DCR-PC100 : NTSC model For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL DCR-PC100E : PAL model ADJUSTMENT MANUAL D MECHANISM ”...
Page 2
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
TABLE OF CONTENTS SERVICE NOTE Recording still images on “Memory Stick”s –Memory photo recording ··················································· 1-28 POWER SUPPLY DURING REPAIRS ····························· 6 Superimposing a still picture in a “Memory Stick” TO TAKE OUT A CASSETTE WHEN NOT EJECT on a moving picture –MEMORY MIX ································ 1-29 (FORCE EJECT) ································································...
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY SELF-DIAGNOSIS FUNCTION When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder, LCD screen or LCD window consists of an alphabet function starts working, and displays on the viewfinder, LCD screen or LCD window what to do.
SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the info LITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Page 9
DCR-PC100/PC100E SECTION 1 This section is extracted from instruction GENERAL manual. (DCR-PC100E model)
DCR-PC100/PC100E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. LCD unit, PD-125 board LCD service position 2-2. MD block-1 MD block service position-1 Note : Use the parts only which can be removed easily from outside of the MD block.
2-6. HINGE ASSEMBLY Perform the disassembling after steps 1 – 6 of 2-1 is complete. 1 Release the claw (a) in the [REMOVING THE HINGE ASSEMBLY] direction of the arrow B first then release the two claws (b). 4 Blind plate assembly 1 PT-125 claw (b) harness...
[SERVICE POSITION (Mainly for voltage measurement and check)] MD block MD frame, Cover assembly MR-44 board - 4 4 Insert an insulation sheet a r d between the MD block and the VC-227 (VC-227P) board. DC-IN connector FJ-25 board (50P) CPC-8 jig AC adaptor MR-44 board...
2-8. CCD/CD BLOCK ASSEMBLY, MF RING BLOCK ASSEMBLY 3 Flexible board 6 CCD/CD block assembly (from lens device) (33P) 4 Tapping screw Never remove the CCD imager (M1.7 × 4) (IC101) from the CD-234 board 2 CD heat sink/ because position alignment CD insulating sheet/ 1 Tapping screw between the CCD imager and...
Page 60
2-10.CONTROL SWITCH BLOCK (FK-4950) 3 FK flexible clamp 5 Screw (M1.7 × 2.5), lock ace, p2 4 Six screws (M1.7 × 2.5), 6 Remove an end of lock ace, p2 the grip belt from 1 Remove the two claws the bracket cap. 2 FP-128 flexible board (30P) 1 Screw (M1.7 ×...
DCR-PC100/PC100E 3-2. POWER BLOCK DIAGRAM-1 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. FJ-25 BOARD VC-227 BOARD(1/2) SHOE ON BATT SIG (4-61) INIT CHARGE ON VTR DD ON BATT FET ON...
DCR-PC100/PC100E POWER BLOCK DIAGRAM-2 ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. VC-227 BOARD IC2204 FP-128 (2/2) (4-38) HI CONTROL (FLEXIBLE) PD-125 BOARD CN002 LCD901 (4-69) SHOE ON BATT SENS...
DCR-PC100/PC100E DCR-PC100/PC100E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 71
DCR-PC100/PC100E CD-234 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-234 Board; 4,000 Series — Do not remove the CCD imager become position alignment between the CCD imager and the CD-234 board is extremely difficult. These two parts are supplied together .
Page 73
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-7 for printed wiring board. • Refer to page 4-87 for waveforms. CD-234 BOARD NO MARK:REC/PB MODE CCD IMAGER -REF.NO.:4000 SERIES- XX MARK:NO MOUNT Schematic diagrams and printed wiring boards C102 R101 0.1u...
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveforms. VC-227 BOARD(1/15) NO MARK:REC/PB MODE R :REC MODE A/D CONVERTER(CH BLOCK) P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT C202...
DCR-PC100/PC100E For Schematic Diagram • Refer to page 4-43 for printed wiring board. • Refer to page 4-87 for waveform. D_3.1V VC-227 BOARD(2/15) FB254 NO MARK:REC/PB MODE 2.8V FB251 CAMERA SIGNAL PROCESSOR R :REC MODE (CA BLOCK) P :PB MODE 1.9V...
Page 79
6-1-5. LENS ASSEMBLY, EVF BLOCK ASSEMBLY not supplied not supplied LCD902 not supplied not supplied not supplied LED902 The CCD imager cannot be replaced as an independent part. Replace the entire CD-234 board (including the CCD imager). Ref. No. Part No. Description Remarks Ref.
Page 80
6-1-6. CASSETTE COMPARTMENT AND DRUM ASSY SECTION FP-242 (See page 6-7) not supplied Attaching procedure not supplied Note M901 Note: Once remove No. 720 CC fastener, don't use it again. Be sure to replace it with new one. (Attaching procedure is as shown above figure.) Ref.
Page 81
6-1-7. LS CHASSIS SECTION Note 1: About FP-242 and FP-92 The FP-242 and FP-92 flexible boards are installed to a chassis with a hot press, which are included in the Ref. No. 762 chassis (D3) assy, LS block section, They are not supplied separately because the high precision for installation is needed. Note 2: Selecting the T washer Select proper parts for the Ref.
Page 82
6-1-8. MECHANISM CHASSIS BLOCK SECTION-1 Note: Be sure to remember the installed position (one of two position), direction and thickness of the Ref. No. 820 (spacer, cap) when the M902 (capstan motor )is removed. Refer to “3-9. Capstan motor” on page 15 in the “DV MECHANICAL ADJUSTMENT MANUAL ”...
Page 84
µF AUS: Australian model Korea model • COILS Tourist model • Model uH: µH CND: Canadian model 100: DCR-PC100 Chinese model 100E: DCR-PC100E Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7031-039-A CCD/CD BLOCK ASSY(SERVICE USE) (100) <...
Page 103
You can find the parts position of location of mount locations applying to VC-227 board of a set. VC-227 SIDE A DCR-PC100/PC100E IC758 CN2903 〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to MR-44 board of a set.
Page 104
〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model Take a copy of CAMERA COLOR DCR-PC100 REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. For PAL model DCR-PC100E — 267 —...