Electronic analytical and precision balances and precious metal scales (56 pages)
Summary of Contents for Sartorius XQ 6100
Page 1
Sartorius XQ 6100, XQ 6100 B. Electronic Paint Mixing Scales Installation and Operating Instructions...
Page 2
[Electrical Installations and Equipment] of April 1986, it is hereby certified that the equipment delivered, "electronic precision scale, model XQ 6100 or XQ 6100 B" is manufactured and tested in compliance with the following DIN/VDE regulations DIN IEC348/VDE0411 Safety requirements for...
Page 4
1 Weighing pan 2 Power receptacle 3 Weight and linear range display 4 TINTER/ADDITIVE key 5 Set 100% key 6 Access switch (for calibration) 7 Tare control 8 PRINT key (functions only if the scale has a built-in interface) 9 RECALL WEIGHT-Taste 10 ON/OFF key 11 %/g key 12 Manufacturer’s label (on the bottom of the...
Do not miss out on the benefits of our warranty. Please fill out the warranty card, indicating the date of installa- tion, and return the card to your Sartorius dealer. Carefully unpack the scale and the accessory components. Save all packing material for future use.
Installation Instructions. Your Sartorius Scale provides exact readouts even under less than ideal conditions. However, exposure to extreme heat, vibrations or drafts may adversely affect the weighing accuracy and should be avoided whenever possible. The scale can be adapted to your particular requirements and to the specific ambient conditions simply by changing the menu code settings in the scale operating program.
Operation. Press the ON/OFF key (10) to turn the scale on or off. The display will go out whenever you turn off the scale. All other circuits will remain energized (STAND-BY state). This means the scale is immediately ready to operate without re- quiring warmup the next time you switch it on.
Page 8
lf you wish to use a Container or if the weight display does not indicate 0.00 g (or the equivalent with the weight unit of your choice), press the tare control to zero the display. Important Note The small circle in the lower left-hand corner shows that the scale has been exactly tared so the display reads "0."...
Examples for Paint Mixing. Example Mix paint components with hardener (35% of the total weight of the paint quantity) and 20% thinner. The 20% thinner is in proportion to the total weight of the paint components and hardener. ——————————————————————————— Place an empty container on the scale and tare ———————————————————————————...
Page 10
You can obtain a display of the total net weight of the paint components by pressing the key (9) ——————————————————————————— To store the total net weight as 100 % – press the key (5) The decimal place will automatically disappear once the total weight is stored as 100 % or "E"...
Page 11
Again, to store the total weight as 100 % – press the key (5) ——————————————————————————— Add 20% thinner Important Note: Make sure that the 20% thinner is in proportion to the total weight of the paint components and to the hardener. ———————————————————————————...
Page 12
Example Mix paint components with 13.5% hardener and 6.5% thinner. These percentages are in proportion to the total weight of the paint quantity paint component + 2nd component = 100%). ——————————————————————————— ^Place empty container on the scale and tare. ——————————————————————————— To weigh in the paint components according to your for- mula and store them, see "1 Example"...
Page 13
To store the total net weight as 100 % - press the key (5) The decimal place will automatically disappear once the total weight is stored as 100 % or "E" will be displayed if the paint components are too light for the particular shade of paint. lf "E"...
Page 14
To add and store the updated total weight, press the key (4) ——————————————————————————— Add 6,5% thinner If you wish to weight in additional components, proceed as described for the hardener and the dinner. ——————————————————————————— Display the total net weight in percent by pressing the key (9) ———————————————————————————...
(5,000 g ± 0.03 g; see Sartorius "Accessories" on page 17), proceed as follows: Remove the protective cap located on the front right of your scale and slide the access switch (6) in the direction of the ar- row.
Page 16
Centre the calibration weight on the weighing pan. Now the weight unit symbol is displayed. lt indicates the end of the calibration procedure. Relock the calibration access function by sliding the access switch back to its original setting, and replace the protective cap.
For information on additional accessories, please contact your dealer. Options: Interface External rechargeable battery Printer Voltage stabilizer Emergency power supply unit Specifications. Model XQ 6100 XQ 6100 B Capacity 6100 6100 Readability Tare range (by subtraction) 6100 6100 Standard deviation ≤± 0,05 ≤± 0,5 Max.
Page 18
All rights reserved. No part of this publication may be printed or translated in any form or by any means without the prior written permission of Sartorius AG. Sartorius AG reserves the right to make change to the technology, features, specification and design of the equipment without notice.