Electronic micro-, analytical and precision balances (84 pages)
Summary of Contents for Sartorius U 4100
Page 1
Sartorius Universal. U 4100, U 4100 S, U 4800 P, U 6100, U 5000 D, U 6100 D, U 6100 S. Electronic Precision Balances...
Page 2
(U 4100, U 6100, U 6100 D only) Menu access switch (for balance operating program) ON/OFF-Taste CAL key PRINT key (functions only if balance has a built-in interface) Tare control Weight display Level indicator (not by U 4100, U 6100, U 6100 D)
Page 4
Equipment] of April 1986,it is hereby certified that the equipment delivered, "electronic precision balance, model U 4100, U 4100 S, U 4800 P, U 6100, U 6100 D or U 6100 S," is manufactured and tested in compliance with the fol-...
-aggressive/corrosive substances -vibrations -drafts. Your Sartorius Balance will provide accurate readouts even when it is exposed to unfavorable conditions. You can adapt it to your requirements simply by changing the menu code set- tings of the balance operating program. For this purpose, please read pages 10 through 12.
AC adapter into a wall outlet. Level the balance using the leveling feet (3) such that air bubble is centered within the circle on the level indicator (10) (not by U 4100, U 6100 und U 6100 D).
Operation. The weight display shows the following special Status messages for your Information: BUSY The processor is still busy processing a function and will not ac- cept any other commands to perform functions at this time. STANDBY The balance has been turned off with the ON/OFF key (5) and is now in the STANDBY mode and ready to operate without warmup.
Page 8
Press the ON/OFF key (5) to switch the balance on or off. You can also turn on the balance with the tare control (8). After the adapter has been plugged into a wall outlet, the weight display will go out when ever you turn off the balance. AII other electronic circuits will remain energized (STANDBY state).This means the balance is immediately ready to operate without re- quiring warmup the next time you switch it on.
Calibration. External Calibration: — Only possible with an accurate calibration weight (U 4100, U 4100 Sand U 4800 P-2,000 g; U 5000 D, U 6100, U 6100 D and U 61OO.S -5,000 g) Please refer to the "Accessories." Clear the pan and press the CAL key (6) (for the U 6100 S use the tare control (8)) for at least three seconds until the calibra- tion weight readout appears in the display.
Balance Operating Program. The balance operating program lets you adapt your balance to various ambient conditions and to different weighing require- ments and select the weight unit(s) commonly used in your country. At the factory we have set the codes for a Standard program, which is protected by a locking function to prevent ac- cidental changes.
Page 11
After the balance operating program has been called the display will show a continuous numerical sequence from 0 to 5 repre- senting the "page" selection, in addition to the Status code letter ''L" or "C.'' When the code number of your choice for the "page" appears, press the tare control.
Page 12
(Active Parameters) Internal Calibration Code Ambient Conditions Code (U 6100 S only) Very stable Accessible (U 4100, U 6100) C 1 1 1 C 1 7 1 Stable Access blocked C 1 1 2 C 1 7 2 Unstable C 1 1 3...
- The balance has not been tared - Tare before weighing before weighing - The air bubble of the level indica- - Level the balance tor is not within the circle (not by U 4100,U 6100 and U 6100 D)
LCD, reflective 7371 01 A for overhead projectors 7371 02 A Calibration weights for: U 4100, U 4100 S, U 4800 P (2 x 1000 g) 7072 08 U 5000 D, U 6100, U 6100 D (1 x 5000 g)
Specifications. Model U 4100 U 4100 S U 4800 P 800/1600/ Capacity 4140 4140 3000/4840 0,01/0,02/ Readability 0,01 0,05/0,1 Tare range (by subtraction)) 4140 4140 4840 ≤±0,01/0,01/ Standard deviation ≤±0,05 ≤±0,01 0,02/0,03 ≤±0,02/0,02/ Max. linearity ≤±0,1 ≤±0,02 0,03/0,05 Stabilization time (typical) Display update 0,1 –...
Page 16
Specifications. Model U 5000 D U 6100 U 6100 D U 6100 S Capacity 500/5050 6100 600/6100 6100 Readability 0,01/0,1 0,01/0,1 0,01 Tare range (by subtraction)) 5050 6100 6100 6100 Standard deviation ≤±0,01/0,05 ≤±0,05 ≤±0,01/0,05 ≤±0,01 Max. linearity ≤±0,01/0,1 ≤±0,1 ≤±0,02/0,1 ≤±0,02 Stabilization time (typical)
Page 18
All rights reserved. No part of this publication may be printed or translated in any form or by any means without the prior written permission of Sartorius AG. Sartorius AG reserves the right to make change to the technology, features, specification and design of the equipment without notice.