NetComm NTC-140-02 User Manual page 103

get ledmode
set ledmode
get ssh.proto
set ssh.proto
get ssh.passauth
set ssh.passauth
get.ssh.keyauth
set.ssh.keyauth
get download.timeout
set download.timeout
get install.timeout
set install.timeout
List of basic RDB variables
The following table lists valid variables where "x" is a profile number (1-6). If no profile is specified, variables are read from or written
to for the current active profile. If a profile is specified, variables are read from or written to for the specified profile number ('x').
# RDB VARIABLE NAME
link.profile.1.enable
link.profile.1.apn
link.profile.1.user
0
link.profile.1.pass
link.profile.1.auth_type
link.profile.1.iplocal
link.profile.1.status
2 link.profile.1.user
3 link.profile.1.pass
4 link.profile.1.auth_type
5 link.profile.1.iplocal
6 wwan.0.radio.information.signal_strength
7 wwan.0.imei
8 statistics.usage_current
9 statistics.usage_current
10 /proc/uptime
11 wwan.0.system_network_status.current_band
www.netcommwireless.com
UM-00012 v1.0
get ledmode
set ledmode=10
get ssh.proto
set ssh.proto=1,2
get ssh.passauth
set ssh.passauth=1
get.ssh.keyauth
set.ssh.keyauth=1
get download.timeout
set download.timeout=20
get install.timeout
set install.timeout=5
Table 34 - List of get/set commands
SMS
VARIABLE
NAME
profile
username
password
authtype
wanip
rssi
imei
usage
wanuptime
deviceuptime
band
Table 35 - List of basic SMS diagnostics RDB variables
Returns the status of the LED operation mode.
Sets the LED operation mode to be always on or to turn off after the specified number of
minutes.
Returns the SSH protocol in use.
Sets the SSH Protocol to protocol 1, 2 or both (1,2).
Returns the status of the SSH Enable password authentication option.
Sets the SSH Enable password authentication option on or off.
Returns the status of the SSH Enable key authentication option.
Sets the SSH Enable key authentication option on or off.
Returns the time in minutes that the router waits before a download times out.
Sets the time in minutes that the router waits before a download times out. This is set to 10
minutes by default. Supported range is 10 – 1440 minutes.
Returns the time in minutes that the router waits before a file that is being installed times out.
Sets the time in minutes that the router waits before a file that is being installed times out. This
is set to 3 minutes by default. Supported range is 3 – 300 minutes.
READ/
DESCRIPTION
WRITE
RW Profile
Cellular broadband
RW
username
Cellular broadband
RW
password
Cellular broadband
RW
Authentication type
R WAN IP address
Cellular signal
R
strength
R IMEI number
Cellular broadband
R data usage of current
session
Up time of current
R cellular broadband
session
R Device up time
R Current band
EXAMPLE VALUE
Read:
(profile no,apn,user,pass,auth,iplocal,status)
1,apn,username,password,
chap,202.44.185.111,up
Write:
(apn, user, pass,auth)
apn,username,password
Guest, could also return "null"
Guest, could also return "null"
"pap" or"chap"
202.44.185.111
-65 dBm
357347050000177
"Rx 500 bytes, Tx 1024 bytes, Total 1524
bytes" or "Rx 0 byte, Tx 0 byte, Total 0 byte"
when wwan down
1 days 02:30:12 or 0 days 00:00:00 when
wwan down
1 days 02:30:12
WCDMA850
NetComm Wireless 4G M2M Router
103