Table of Contents
Advertisement
List of get/set commands
The following table is a partial list of get and set commands which may be performed via SMS.
COMMAND
NAME
get status
get sessionhistory
set syslogserver
get plmnscan
set forceplmn
get forceplmn
get pppoe
set pppoe
get ledmode
set ledmode
get ssh.proto
set ssh.proto
get ssh.passauth
set ssh.passauth
get.ssh.keyauth
set.ssh.keyauth
List of basic RDB variables
The following table lists valid variables where "x" is a profile number (1-6). If no profile is specified, variables are read from or written
to for the current active profile. If a profile is specified, variables are read from or written to for the specified profile number ('x').
#
RDB VARIABLE NAME
link.profile.1.enable
link.profile.1.apn
link.profile.1.user
0
link.profile.1.pass
link.profile.1.auth_type
link.profile.1.iplocal
link.profile.1.status
2
link.profile.1.user
3
link.profile.1.pass
4
link.profile.1.auth_type
5
link.profile.1.iplocal
6
wwan.0.radio.information.signal_strength
7
wwan.0.imei
8
statistics.usage_current
statistics.usage_current
9
NetComm Wireless NTC-40WV Industrial Indoor 3G Router with Voice
94
EXAMPLE
get status
get sessionhistory
set
syslogserver=123.45.67.89:514
get plmnscan
set forceplmn=505,3
get forceplmn
get pppoe
set pppoe=1, telstra.internet, test
get ledmode
set ledmode=10
get ssh.proto
set ssh.proto=1,2
get ssh.passauth
set ssh.passauth=1
get.ssh.keyauth
set.ssh.keyauth=1
Table 26 - List of get/set commands
SMS VARIABLE
NAME
profile
username
password
authtype
wanip
rssi
imei
usage
wanuptime
Returns the Module firmware version, LAN IP Address, Network State, Network operator and
RSSI.
Returns the time and date of recent sessions along with the total amount of data sent and
received for each session.
Sets a remote syslog server IP or hostname and port.
Instructs the router to perform a network scan and returns the results by SMS.
Sets the operator to a manual selection made by the user where "505" is the Mobile Country
Code for Australia and "3" is the Mobile Network Code for Vodafone. As no network type (i.e.
3G or 2G) is specified, it is selected automatically.
Returns the operator and network type selection mode (Automatic/Manual), in addition to the
MCC and MNC values
Returns the PPPoE status, currently configured dial string and service name
Sets the PPPoE status on, APN to telstra.internet, and service name to test.
Returns the status of the LED operation mode.
Sets the LED operation mode to be always on or to turn off after the specified number of
minutes.
Returns the SSH protocol in use.
Sets the SSH Protocol to protocol 1, 2 or both (1,2).
Returns the status of the SSH Enable password authentication option.
Sets the SSH Enable password authentication option on or off.
Returns the status of the SSH Enable key authentication option.
Sets the SSH Enable key authentication option on or off.
READ/
DESCRIPTION
WRITE
RW
Profile
RW
3G username
RW
3G password
3G Authentication
RW
type
R
WAN IP address
R
3G signal strength
R
IMEI number
3G data usage of
R
current session
Up time of current 3G
R
session
DESCRIPTION
EXAMPLE VALUE
Read:
(profile no,apn,user,pass,auth,iplocal,status)
1,apn,username,password,
chap,202.44.185.111,up
Write:
(apn, user, pass,auth)
apn,username,password
Guest, could also return "null"
Guest, could also return "null"
"pap" or"chap"
202.44.185.111
-65 dBm
357347050000177
"Rx 500 bytes, Tx 1024 bytes, Total 1524
bytes" or "Rx 0 byte, Tx 0 byte, Total 0 byte"
when wwan down
1 days 02:30:12 or 0 days 00:00:00 when
wwan down
www.netcommwireless.com
Ver 1.4
Advertisement
Table of Contents
