Hardware Setup; Hardware Config - Onkyo TX-SR601E Instruction Manual

Hardware Setup

Hardware Config
To display the Hardware Config menu:
1. Display the main menu.
2. Use the and cursor buttons to select "1. Hardware
Config" and then press the ENTER button. The "Hardware
Config" menu appears.
TX-SR701/701E
* Menu *****************
1.Speaker Config
1.Hardware Config
2.Speaker Distance
***********************
3.Level Calibration
4.Input Setup
a.Surr/Zone 2:Surr
5.OSD Setup
b.Surr Back : 1ch
6.Preference
c.IR IN Position
:Main
d.TV Format :Auto
e.AM Frequency Step
:9kHz
Quit:|SETUP|
a. Surr/Zone 2
If you connect the Zone 2 speakers to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT (TX-
SR701/701E only) terminals, set the Surr/Zone 2 setting to "Zone
2."
Surr: In this setting, sound will not be output from the Zone 2
speakers which is connected to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT
(TX-SR701/701E only) terminals. In the main room, 6.1-
channel playback will always be available.
Zone 2: In this setting, when you are not using the Zone 2, 6.1-
channel playback will be available for the main room. However,
while you use the Zone 2, 6.1-channel playback will not be
available for the main room (2ch stereo playback only).
b. Surr Back (TX-SR701/701E only)
Specify whether you use one surround back speaker or two.
1ch: Selects when you connect one surround back speaker to
the SURROUND BACK SPEAKER terminals on the TX-
SR701/701E.
2ch (PRE OUT): Selects when you connect two surround back
speakers to the power amplifier connected to the SURR BACK
PRE OUT terminals on the TX-SR701/701E.
Note:
Be sure to use either one or two surround back speakers.
Connecting surround back speakers to both the SURROUND
BACK SPEAKER terminals on the TX-SR701/701E and the power
amplifier will not produce correct surround sound effect.
c. IR IN Position (TX-SR701/701E)
b. IR IN Position (TX-SR601/601E)
Use this setting when you have a remote control sensor connected
to the IR IN terminal. The setting in this menu tells the TX-SR701/
701E/601/601E whether the remote control sensor is being used for
operation of the TX-SR701/701E/601/601E in the main zone or the
remote zone (Zone 2).
Main: Select when you are using the remote control sensor for
operation with the remote controller in the main zone.
Zone 2: Select when you are using the remote control sensor
for operation with the remote controller in the remote zone
(Zone 2).
TX-SR601/601E
* Menu *****************
1.Speaker Config
1.Hardware Config
2.Speaker Distance
***********************
3.Level Calibration
4.Input Setup
a.Surr/Zone 2 :Surr
5.OSD Setup
b.IR IN Position
6.Preference
:Main
c.TV Format :Auto
d.AM Frequency Step
:9kHz
Quit:|SETUP|
d. TV Format (TX-SR701/701E)
c. TV Format (TX-SR601/601E)
(For all models other than USA and Canadian models)
The default setting is "Auto," which means that the television
format is detected and automatically set by the TX-SR701/701E/
601/601E. However, if you know the correct format, you can use
this setting to choose either PAL or NTSC so that no time is wasted
on detection.
e. AM Frequency Step (TX-SR701/701E)
d. AM Frequency Step (TX-SR601/601E)
This setting only appears on the worldwide model. It determines the
increment amount or decrement amount when adjusting the AM
tuner frequency. The initial setting is 9 kHz, and this needs only to
be changed if you are using the TX-SR701/701E/601/601E in a 10-
kHz region.
55