Onkyo TX-SR601E Instruction Manual page 32

Configuring the speakers
4. Use the and cursor buttons to select "Subwoofer"
and then use the and
subwoofer setting.
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
TX-SR701/701E/601/601E
TUNI NG
PRESET
TUNI NG
PRESET
5. Use the and cursor buttons to select "Front L/R"
and then use the and
front speaker setting.
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
• If "No" is selected for the Subwoofer setting, this setting is
fixed to "Large."
6. Use the and cursor buttons to select "Center"
and then use the and
center speaker setting.
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
• If "Small" is selected for the Front setting, "Large" cannot
be selected for this setting.
7. Use the and cursor buttons to select "Surround L/
R" and then use the
the surround speaker setting.
None: Select if no surround left and right speakers are
connected.
Large: Select if the surround left and right speakers are large
sized.
Small: Select if the surround left and right speakers are small
sized.
• If "Small" is selected for the Front setting, "Large" cannot
be selected for this setting.
8. Use the and cursor buttons to select "Surround
back" and then use the
select the surround back speaker setting.
None: Select if no surround back speaker is connected.
Large: Select if the surround back speaker is large sized.
Small: Select if the surround back speaker is small sized.
• If "None" is selected for the Surround setting, this setting
will be disabled.
• If "Small" is selected for the Surround setting, "Large"
cannot be selected for this setting.
32
cursor buttons to select the
Remote controller
cursor buttons to select the
cursor buttons to select the
and cursor buttons to select
and cursor buttons to
9. Use the and cursor buttons to select "Crossover"
and then use the and
crossover frequency mode setting.
Adjustable Crossover for Bass Management
TX-SR701/701E
f. Crossover
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum
frequency delivered to a speaker and can be set to 40 Hz, 60 Hz,
80 Hz (THX), 100 Hz, 120 Hz, or 150Hz. Select "80Hz (THX)"
if you are using a THX-certified speaker system. This setting is
valid when "Subwoofer" is set to "Yes," or for speakers that are
set to "Small," at the "Speaker Config" menu. Frequencies
below this are cut from speakers set to "Small" and sent to the
subwoofer (or to speakers set to "Large").
Note:
When "Large" is set, the complete frequency range for that
speaker channel will be output. When "Small" is set, the
frequencies below 80 Hz for that speaker channel are output to
the subwoofer. If Subwoofer is set to "No" in the Speaker
Config menu, then they will be output to the left and right front
speakers. (Set all speakers for THX speaker systems to "small.")
TX-SR601/601E
f. Crossover
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum
frequency delivered to a speaker and can be set to 60 Hz, 80 Hz,
100 Hz, 120 Hz, or 150Hz. This setting is valid when
"Subwoofer" is set to "Yes," or for speakers that are set to
"Small," at the "Speaker Config" menu. Frequencies below this
are cut from speakers set to "Small" and sent to the subwoofer
(or to speakers set to "Large").
The following table lists the crossover frequency you should
choose depending on the diameter of your front spekers.
Front speaker diameter
Larger than 12" (30cm)
8"~12" (20-30 cm)
6-1/2"~8" (16-20 cm)
5-1/4"~6-1/2" (13-16cm)
3-1/2"~5-1/4" (9-13 cm)
Less than 3-1/2" (9 cm)
Note:
When "Large" is set, the complete frequency range for that
speaker channel will be output. When "Small" is set, the
frequencies below 80 Hz for that speaker channel are output to
the subwoofer. If Subwoofer is set to "No" in the 1-1. Speaker
Config Sub-menu, then they will be output to the left and right
front speakers.
Press the RETURN button to return to the main menu.
Press the SETUP button on the front panel or on the remote
controller to exit the Setup menu.
cursor buttons to select the
crosscover frequency
40
60
80
100
120
150