Page 1
Elliptical X-350p OWNER’S MANUAL CAUTION: Exercise of a strenuous nature, as is customarily done on this equipment, should not be undertaken without first consulting a physician. No specific health claims are made or implied as they relate to the equipment.
ATTACHMENT - A IMPORTANT SAFETY ADVICE PRECAUTIONS This elliptical has been designed and constructed to provide maximum safety. Nevertheless, certain precautions should be taken when using exercise equipment. Read the whole manual before assembling and using the elliptical. The following safety precautions should also be observed: 1.
HARDWARE PACKAGE /PARTS/ TOOLS Note: Use the tools only for this elliptical. Power adapter Water Bottle Holder Handlebar attachment cover Base Frame Wrench Hex head bolt Upright Tube M8 * 15/Allen head bolt Console M10/End cap Pedal Support (right) Plastic cap/M8 Bushing/57.6MM Pedal Support (left) Bushing/15MM...
PRE-ASSEMBLY INSTRUCTIONS GENERAL INSTRUCTIONS Carefully read through the instructions contained in this manual. It provides you with important information about assembly, safety and use of the machine. 1. This unit has been designed for home use. The weight of the user must not exceed 255 lbs. (116 kg.) 2.
ASSEMBLY INSTRUCTIONS STEP #1. Attach the Front Stabilizer (73) to the bottom front portion of the Base Frame (64) using the screw (19), washer (62), nylock nut (20), and plastic cap (21) combination, as shown in illustration #1. Illustration #1 STEP #2.
Page 8
ASSEMBLY INSTRUCTIONS STEP #3. This step may require the assistance of an additional person. Join the male and female connectors ends that attach the console control wire to the Base Frame (64). Now slide the Upright Tube (65) into the Base Frame (64), paying close attention not cut or pinch the control wires.
Page 9
ASSEMBLY INSTRUCTIONS STEP #5. Attach the Left Pedal Tube (71) to the Flywheel Shaft using the bushings (79&80), washer (17), nylock nut (12), and plastic cap (5) combination, as shown in illustration #5. Now repeat the process for the Right Pedal tube using the same steps.
Page 10
ASSEMBLY INSTRUCTIONS STEP #7. Attach the (left) handlebar (69) and (right) handlebar (70) to the top of the corresponding swivel tube. Secure the attached members using the screws (18) supplied, as shown in Illustration #7. Illustration #7 STEP #8. Pull the pulse sensor cable up to the console mount using the pull wire, which is secured to the top of the Upright Tube (65).
Page 11
ASSEMBLY INSTRUCTIONS STEP #9. PLEASE DO NOT PINCH OR CUT OR PINCH THE CONTROL WIRING. Join the male and female ends of the connectors that attach the console control wire to the Upper portion of the swivel tube. Now attach the console to the upper mount of the swivel tube using screws provided, as shown in figure #9.
3. SCAN Pulse is measured by sensors in the handlebars. Starts scanning between values of speed – distance Pulse is measured when the user of Bladez X-350P – calories on the middle window. is touching both sensors simultaneously. Reliable pulse measurement requires that the skin is 4.
Page 13
ELLIPTICAL OPERATIONS (CONTINUED) PROGRAMS Start the recovery calculation after training by 1. MANUAL AND PRESET PROGRAMS pressing RECOVERY button. Recovery heart rate calculation can be started only if the heart rate •Press the PROGRAM button to browse P01-P12 or measurement is activated and the heart rate value Manual (MAN) programs.
MAINTENANCE INSTRUCTIONS CLEANING Care has been taken to assure that your bike has been properly adjusted and lubricated at the factory. It is not recommended that the user attempt service on the internal components instead seek service from an authorized service center. However, from time-to-time the outer surfaces may appear dull or dirty, following the instructions listed below will restore and preserve the original finish.
Elliptical X-350P PARTS LIST Key Number Description Key Number Description Handlebar end cap Pedal, LH Handlebar grip Pedal, RH T-Bar grip End cap Hand pulse grip unit End cap End cap (T-Bar) Hex head bolt Middle cover, LH Locking washer...
COMMERCIAL OR RENTAL USE If a Bladez Elliptical product is used for commercial or rental purposes the warranty is void. THIS WARRANTY DOES NOT COVER •...