Oneida Air Systems V - 2000 2hp Owner's Manual
  1. Manuals
  2. Brands
  3. Oneida Air Systems Manuals
  4. Dust Collector
  5. V - 2000 2hp
  6. Owner's manual

Oneida Air Systems V - 2000 2hp Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

V-SYSTEMS
Powerful Economical Made in the USA
6_08
V-SYSTEMS
Appearance may vary sligthly.
V - 2000 2hp / V - 3000 3hp Dust Collector Owner's Manual
1.800.732.4065
www.oneida-air.com
1001 W. Fayette St., Syracuse, NY 13204
Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art
dust collection systems and material handling ductwork to woodworking shops. OAS
designs and manufactures industrial grade dust collection systems that create a prac-
tical, safe and healthy work place environment.

Advertisement

Table of Contents
loading

Related Manuals for Oneida Air Systems V - 2000 2hp

Summary of Contents for Oneida Air Systems V - 2000 2hp

  • Page 1 Powerful Economical Made in the USA 6_08 V-SYSTEMS Appearance may vary sligthly. V - 2000 2hp / V - 3000 3hp Dust Collector Owner’s Manual 1.800.732.4065 www.oneida-air.com 1001 W. Fayette St., Syracuse, NY 13204 Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art dust collection systems and material handling ductwork to woodworking shops.

  • Page 2: Table Of Contents

    Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 7:30am - 6:00pm EST Mon. - Thurs. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection.

  • Page 3: System Start-Up Information

    I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual Warning Do not operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place.

  • Page 4: System Specifications

    Shop Plan Design Service *Oneida reserves the right to change or modify specs and system appearance without notice. 24” Actual system appearance may vary. Oneida V - 2000 2hp / V - 3000 3hp Part # Description XXV020126 V-2000 w/ Blended Filter...

  • Page 5: Parts List

    III. Parts List V-Systems Motor Box - BXI020107 (2hp) / BXI030107 (3hp) 1. Motor / Blower Assembly - BXI020107 (2hp) / BXI030107 (3hp) 1a. Motor (1) - BMZ020105 (2hp) / BMZ030170 (3hp) 1b. Pre-Wired Mag. Starter w/ Remote Option (1) - AMR221114 (2hp) (1) - AMR221417 (3hp) 1c.

  • Page 6: Fan Wheel Motor Assembly

    IV. V-Systems Fan Wheel Motor Assembly Note that Magnetic Starter is attached 1. Open box and unpack Motor, Mag- to Motor by it’s cord. netic Starter, Fan Wheel and Hardware package. Wheel and Hardware pack- age is packed underneath Motor. See right.

  • Page 7: Fan Wheel Motor Assembly

    7. Put Fan Housing topside down over Fan Housing holes should line up with motor shaft and line up the bolt holes Motor bolt holes. as shown below. 8. Put included Lock-Tite on bolt shafts and put all four bolts with Lock Washer in the holes and finger tighten.

  • Page 8: Cyclone Leg Assembly

    V. V-Systems Cone Leg Assembly 13. Insert legs into triangular holders 12. Put included self-sticking gasket 14. Pick up cyclone and tighten bolts securely. on top rim of cone. Make sure there is and set up on legs. NO gap where both ends of gasket meet.

  • Page 9: Plenum Elbow Assembly

    VI. V-Systems Plenum Elbow Assembly 19. Attach plenum with sheet metal screws and seal well with silicone to prevent dust blow out.. VII. V-Systems Filter Assembly Plastic ring on Silencer must sit on the Insert Silencer into Filter. If you have the Spun-Bond Filter you inside of the Filter gasket.

  • Page 10: Drum Assembly

    Fit over Filter rim. 22. Position top of clip over metal rim, then push bottom of clip underneath the rim of the dust pan. Space the three clips equally around the dust Side view pan, making sure the pan is even with of clip.

  • Page 11: Directions For Cleaning Filter

    IX. Directions for Cleaning External Filter All steps should be done with a dust mask and eye protection. The Filter can be cleaned using the following methods: 1. Compressed air from outside. Blast air along pleats of the filter at about a 20 degree angle. Blast air out and away from you or anyone in the general area.

  • Page 12: Electrical Data

    X. V - Systems Electrical Data Always Use A Licensed, Professional Electrician. Customer supplied receptacle fed from 2 pole dedicated circuit breaker. 6 - 20R 6 - 20P Note: This dust collector is pre- wired at the factory and need only Magnetic Starter - be plugged into a dedicated NEMA Mount close to...

  • Page 13: Troubleshooting

    XI. Troubleshooting Unplug unit before servicing or cleaning. V - Systems Owner’s Manual O.A.S. 2008...

  • Page 14: Fire Hazards

    XII. Fire Hazards - Read Before Installing and Operating Oneida Collectors are designed for WOOD DUST only!! Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly).

  • Page 15: Terms And Conditions

    Oneida Air Systems shall be tried in the State of New York, County of Onondaga. Oneida Air Systems shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our product.

  • Page 16: Fan Motor Maintenance

    XIV. Fan Motor Maintenance Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated every 5500 hours. Table 1 - Service Conditions Table 2 - Lubrication Interval Multiplier Per Baldor specifications, add .30 ounces (8.4 grams) of Mobil Polyrex grease by weight or .6 cubic inches (2 teaspoons) of Mobil Polyrex grease by volume.

This manual is also suitable for:

V - 3000 3hp

Table of Contents