AP 6522M Access Point
INSTALLATION GUIDE

   Also See for Motorola AP 6522M

   Summary of Contents for Motorola AP 6522M

  • Page 1

    AP 6522M Access Point INSTALLATION GUIDE...

  • Page 2

    AP 6522M Access Point Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. © 2015 Symbol Technologies, Inc...

  • Page 3: Table Of Contents

    4.1 AP 6522M Integrated Antenna Model Electrical Characteristics ... . . 25 4.2 AP 6522M Integrated Antenna Model Physical Characteristics ....25 4.3 Radio Characteristics .

  • Page 4: Table Of Contents

    AP 6522M Access Point 5.1.3 Safety in Hospitals ......... . . 29 5.3 RF Exposure Guidelines .

  • Page 5: Introduction

    Points. The AP 6522M Access Point provides multiple deployment options. The AP 6522M Access Point receives all power and transfers data through the same CAT-5 or better Ethernet cable. An 802.3af Ethernet switch or power supply (specifically rated for the AP 6522M) is required (Part No.

  • Page 6: Warnings

    • Identify and prepare Ethernet and console port connections. • Verify cable lengths are within the maximum allowable distances for optimal signal transmission. 1.4 Package Contents An AP 6522M Access Point ships with the following: • AP 6522M Access Point with internal antennas •...

  • Page 7: Features

    • Clips for mounting on a suspended ceiling T-bar (internal antenna model only) with separately orderable accessories The AP 6522M Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and accepts 802.3af-compliant power from an external source. The illustration below is of an integrated antenna model.

  • Page 8: Hardware Installation

    2.1 Installation Instructions The AP 6522M Access Point mounts either on a wall (with customer supplied M4 x 25 pan head screws and wall anchor - or equivalent) or on a suspended ceiling T-bar. An AP 6522M is not designed for mounting on a desk.

  • Page 9: Precautions

    2.4 Wall Mount Instructions Wall mounting requires hanging the AP 6522M along its width or length using the two slots on the bottom of the unit. The AP 6522M can be mounted on to any plaster, wood, or cement wall surface using customer supplied screw hardware (M3.5 x 0.6 x 20 mm- or equivalent).

  • Page 10: Wall Mount Procedure

    When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.). NOTE 4. Attach an Ethernet cable from the Access Point to a controller with an 802.3af-compatible power source or use the PWRS-14000-148R power supply to supply power to the AP 6522M (once fully cabled).

  • Page 11

    6. Slide the case down along the mounting surface to hang the mount slots on the screw heads. 7. Verify the unit has power by observing that the LEDs are lit or flashing. If not using a 802.3af capable controller to power the AP 6522M, CAUTION ensure only the AP 6522M’s designated power supply...

  • Page 12: Suspended Ceiling T-bar Mount

    AP 6522M Access Point 2.5 Suspended Ceiling T-Bar Mount Ceiling mount requires holding the AP 6522M Access Point up against a T-bar of a suspended ceiling grid and twisting the case onto the T-bar. 2.5.1 Suspended Ceiling T-Bar Mount Procedure 1.

  • Page 13: Led Indicators

    2.6 LED Indicators AP 6522M Access Points have LED activity indicators on the side of the case. The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11an (amber) radio or the 2.4 GHz 802.11bgn (green) radio.

  • Page 14: Initial Access Point Configuration

    1. Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source or use the PWRS-14000-148R power supply to supply power to the AP 6522M (once fully cabled). If your host system is a DHCP server, an IP address is automatically assigned to the Access Point and can be used for device connection.

  • Page 15

    Installation Guide 5. Click the Login button to load the management interface. When logging in for the first time, you’re prompted to change the NOTE password to enhance device security in subsequent logins. If you get disconnected when running the wizard, you can connect again NOTE with the Access Point’s actual IP address (once obtained) and resume the wizard.

  • Page 16

    AP 6522M Access Point Use the Choose One type to Setup the Access Point field options to select the type of wizard to run. The Typical Setup is the recommended wizard. This wizard uses the default parameters for most of the configuration parameters and sets up a working network with the least amount of manual configuration.

  • Page 17

    Installation Guide For information on using the Access Point’s Advanced Setup option, refer to the WiNG Access Point System Reference Guide to familiarize yourself with the feature set supported by the WiNG operating system. The guide is available at www.zebra.com/support. To configure the Access Point using the Typical Setup Wizard: 8.

  • Page 18

    AP 6522M Access Point If designating the Access Point as a Standalone AP, it is recommended NOTE the Access Point’s UI be used exclusively to define its device configuration, and not the CLI. The CLI provides the ability to define more than one profile and the UI does not.

  • Page 19

    Installation Guide • Router Mode -In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point. • Bridge Mode - In Bridge Mode, the Access Point depends on an external router for routing LAN and WAN traffic.

  • Page 20

    AP 6522M Access Point 15. Set the following DHCP and Static IP Address/Subnet information for the LAN interface: • Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Point’s DHCP server. • Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's LAN interface. If Use DHCP is selected, this field is not available.

  • Page 21

    Installation Guide 16. Select Next. The Typical Setup Wizard displays the Wireless LAN Setup screen to set the Access Point’s Wireless LAN interface configuration. 17. Set the following WLAN1 Configuration parameters: • SSID - Configure the SSID for the WLAN. •...

  • Page 22

    AP 6522M Access Point 19. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use the screen to add, modify and remove RADIUS users. 20. Select Add User to display the dialog to enter user information to add to the RADIUS server user...

  • Page 23

    Installation Guide 21. Enter the following user information: • Username - Provide a user name used to authenticate the user. • Password - Provide a password used to authenticate the user. • Confirm Password - Confirm the password by entering the same password as entered in the Password field.

  • Page 24

    AP 6522M Access Point 27. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings updated using the Typical Setup Wizard. No user intervention or additional settings are required. Its an additional means of validating the Access Point’s updated configuration before it’s deployed.

  • Page 25: Specifications

    Installation Guide Specifications 4.1 AP 6522M Integrated Antenna Model Electrical Characteristics An AP 6522M Integrated model Access Point has the following electrical characteristics: Operating Current & 12VDC, 1A (accessory power connector) Voltage 48V,0.25A (PoE connector) 4.2 AP 6522M Integrated Antenna Model Physical Characteristics...

  • Page 26: Radio Characteristics

    AP 6522M Access Point 4.3 Radio Characteristics The AP 6522M model Access Points have the following radio characteristics: Operating Channels All channels from 4920 MHz to 5825 MHz except channel 52 -64 Channels 1-13 (2412-2472 MHz) Channel 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory approval for the country of use.

  • Page 27: Regulatory Information

    Installation Guide Regulatory Information This guide applies to MODEL: AP-0622 (Part Number AP-6522M). All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following Website: www.zebra.com/support.

  • Page 28: Frequency Of Operation - Fcc And Ic

    AP 6522M Access Point 5.1.2 Frequency of Operation – FCC and IC 5 GHz Only The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor Use Only; any other use will make the operation of this device illegal.

  • Page 29: Safety In Hospitals

    Installation Guide 5.2.3 Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.

  • Page 30: Power Supply

    AP 6522M Access Point US and Canada Co-located statement To comply with FCC RF exposure compliance requirement, the antennas used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling.

  • Page 31: Radio Frequency Interference Requirements - Canada

    Installation Guide 5.5.2 Radio Frequency Interference Requirements – Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s) Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 32: Statement Of Compliance

    AP 6522M Access Point 5.6 CE Marking and European Economic Area (EEA) The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions: • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.

  • Page 33

    Installation Guide Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage.

  • Page 34: Turkish Weee Statement Of Compliance

    AP 6522M Access Point Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/weee. Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare.

  • Page 35: Other Countries

    Installation Guide 5.8 Other Countries Japan (VCCI) - Voluntary Control Council for Interference この装置は、情報処理装置等電 波障害自主規制協議会(VCCI)の基準に基づくクラスB情 報技術装置です。この装置は、家庭環境で使 用することを目的としていますが、この装置がラ ジオやテレビジョン受信機に近接して使用さ れると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。 Korea Warning Statement for Class B Australia Use of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz. Brazil Declarações Regulamentares para - Brasil Nota: A marca de certificação se aplica ao Transceptor, modelo .

  • Page 36

    AP 6522M Access Point Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. "La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada."...

  • Page 37: Support

    Installation Guide Support If you have a problem with your equipment, contact support for your region. Contact information is available at: www.zebra.com/support. When contacting support, please provide the following information: • Serial number of the unit • Model number or product name •...

  • Page 38: Symbol Technologies End-user Software License Agreement

    AP 6522M Access Point Symbol Technologies End-User Software License Agreement This End-User Software License Agreement ("End-User License Agreement") is between Symbol Technologies Inc. (herein "Symbol Technologies") and End-User Customer to whom Symbol Technologies' proprietary software or Symbol Technologies Products containing embedded, pre-loaded, or installed software ("Products") is made available.

  • Page 39

    Installation Guide If the Software licensed under this End-User License Agreement contains or is derived from Open Source Software, the terms and conditions governing the use of such Open Source Software are in the Open Source Software Licenses of the copyright owner and not this End-User License Agreement. If there is a conflict between the terms and conditions of this End-User License Agreement and the terms and conditions of the Open Source Software Licenses governing End-User Customer’s use of the Open Source Software, the terms and conditions of the license grant of the applicable Open Source Software Licenses...

  • Page 40

    AP 6522M Access Point operated. End-User Customer may make as many copies of the Documentation as it may reasonably require for the internal use of the Software. Unless otherwise authorized by Symbol Technologies in writing, End-User Customer will not, and will not enable or allow any third party to: (i) install a licensed copy of the Software on more than one unit of a Product;...

  • Page 41

    Installation Guide 6. CONFIDENTIALITY End-User Customer acknowledges that the Software contains valuable proprietary information and trade secrets and that unauthorized dissemination, distribution, modification, reverse engineering, disassembly or other improper use of the Software will result in irreparable harm to Symbol Technologies for which monetary damages would be inadequate.

  • Page 42

    AP 6522M Access Point BE DISCLAIMED BY LAW, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE LIMITATIONS IN THIS PARAGRAPH WILL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY. 9. TERM AND TERMINATION Any use of the Software, including but not limited to use on the Products, will constitute End-User Customer’s agreement to this End-User License Agreement.

  • Page 43

    Installation Guide consistent with the rights provided to the End-User Customer under the provisions of the FAR and DFARS mentioned above, as applicable to the particular procuring agency and procurement transaction. 11. GENERAL 11.1 Copyright Notices. The existence of a copyright notice on the Software will not be construed as an admission or presumption that public disclosure of the Software or any trade secrets associated with the Software has occurred.

  • Page 44

    AP 6522M Access Point 11.8 Governing Law. This End-User License Agreement is governed by the laws of the the State of Delaware in the United States to the extent that they apply and otherwise by the internal substantive laws of the country to which the Software is shipped if End-User Customer is a sovereign governmental entity.

  • Page 45

    Installation Guide...

  • Page 46

    AP 6522M Access Point...

  • Page 47

    Installation Guide...

  • Page 48

    Zebra Technologies Corporation. 475 Half Day Road, Suite 500, Lincolnshire, IL 60069 USA Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. ©...

Comments to this Manuals

Symbols: 0
Latest comments: