Download Print this page

Advertisement

AP6562 Access Point
INSTALLATION GUIDE

Advertisement

   Also See for Motorola AP6562

   Summary of Contents for Motorola AP6562

  • Page 1

    AP6562 Access Point INSTALLATION GUIDE...

  • Page 2

    AP6562 Access Point...

  • Page 3: Table Of Contents

    2.2 Access Point Placement..........10 2.3 AP6562 Hardware Mouting and Installation......10 2.3.1 Mounting Bracket Kit .

  • Page 4

    AP6562 Access Point 6.0 Motorola Solutions Support Center ....... . . 50 7.0 Motorola Solutions Software End-User License Agreement .

  • Page 5

    Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design. Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or any product, circuit, or application described herein.

  • Page 6: Introduction

    The AP6562 access point provides multiple deployment options. The AP6562 access point receives all power and transfers data through the same CAT-5 or better Ethernet cable. An 802.3at Ethernet switch or power supply (specifically rated for the AP6562) is required.

  • Page 7: Warnings

    • Verify cable lengths are within the maximum allowable distances for optimal signal transmission. 1.4 AP6562 Package Contents An AP6562 access point is available in internal antenna and external antenna models. Contents differ depending on the model ordered. 1.4.1 Internal Antenna Model Package Contents...

  • Page 8: External Antenna Model Package Contents

    Gigabit operation. The AP6562 access point comes with dual radios supporting 802.11abgn. The access point contains runtime firmware which enables the unit to boot after a power up. The runtime firmware on the access point and the...

  • Page 9: Hardware Installation

    1. Match the model number on the purchase order with the model numbers in the packing list and on the case of the access point. 2. Verify the contents of the box include the intended AP6562 access point, and the included hardware Internal Antenna Model...

  • Page 10: Access Point Placement

    2.3 AP6562 Hardware Mounting and Installation It is recommended to use the AP6562 mounting bracket kit (KT-147407-01) for most deployments. When a standoff distance is required for a pole mounted or wall mounted installation, use the extension arm kit (KT-150173-01).

  • Page 11: Extension Arm Kit

    2.3.2 Extension Arm Kit When mounting an AP6562 on poles more than 3 inches in diameter, use the extension arm kit (KT-150173-01) to provide a minimum standoff distance of twelve inches to avoid interference with the antennas. The extension arm...

  • Page 12: Pole Mounted Installations

    2.3.3 Pole Mounted Installations The mounting hardware kit and extension arm can be used in various combinations to properly install the AP6562 on a pole. For poles of up to 3 inches in diameter, attach the pole mount bracket of the mounting hardware kit at the desired position on the pole using band clamps up to 3/4 inch width, or a 1/2 inch x 4 inch wide U-bolt and nuts.

  • Page 13: Pole Mount Installations

    10mm socket, or an adjustable wrench, attach (but don’t tighten) the access point bracket section to the AP6562 with the with four M6 hex flange screws. 7. Insert two M6 hex flange screws into the bottom holes on the sides of the access point bracket section.

  • Page 14

    9. If required, install and attach a Kensington security cable (customer supplied) to the unit’s lock port. 10. Attach an Ethernet cable from the access point to a controller with an 802.3at-compatible power source or use the PWRS-14000-148R power supply to supply power to the AP6562 (once fully cabled).

  • Page 15

    6. Attach an Ethernet cable from the access point to a controller with an 802.3at-compatible power source or use the AP-PSBIAS-7161 power supply to supply power to the AP6562 (once fully cabled). 7. Verify the unit has power by observing that the LEDs are lit or flashing.

  • Page 16: Wall Mounted Installation

    2. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the access point bracket section to the AP6562 with four M6 hex flange screws and insert two M6 hex flange screws into the bottom holes on the sides of the access point bracket section.

  • Page 17

    Installation Guide 10. Verify the unit has power by observing that the LEDs are lit or flashing. If not using a 802.3at capable controller to power the AP6562, ensure CAUTION only the AP6562’s designated outdoor power supply (AP-PSBIAS-7161-US or AP-PSBIAS-7161-WW) is used to supply power to the access point.

  • Page 18

    AP6562 Access Point 2.4 AP6562 Internal Antenna Model AP6562 internal antenna models (AP-6562-66030-US, AP-6562-66030-WR and AP-6562-66030-EU) are configured with four internal antennas.

  • Page 19

    Installation Guide 2.5 AP6562 External Antenna Model AP6562 external antenna models ( AP-6562-66040-US, AP-6562-66040-WR and AP-6562-66040-EU) are configured with four external N type connectors.

  • Page 20

    The labels for Radio 1-0, Radio 1-1, Radio 2-0 and Radio 2-1 are molded into the AP6562 access point enclosure beside the antenna connectors. When mounting antennas to the connectors, ensure that you have selected the appropriate band for the configured radio.

  • Page 21: Ap6562 Led Indicators

    Installation Guide 2.6 AP6562 LED Indicators Both internal antenna and external antenna models have LED activity indicators on the front of the case.

  • Page 22

    AP6562 Access Point The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11an (amber) radio or the 2.4 GHz 802.11bgn (green) radio. Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)

  • Page 23: Initial Access Point Configuration

    PWRS-14000-148R power supply to supply power to the AP6562 (once fully cabled). If your host system is a DHCP server, an IP address is automatically assigned to the AP6562 and can be used for device connection. However, if a DHCP server is not available, you’ll need to derive the IP address from the AP6562 MAC address.

  • Page 24

    6. Select the Start Wizard button to run the initial setup wizard. The setup wizard displays the first time the AP6562 user interface is accessed in order to define the AP6562’s initial configuration. 7. If this is the first time the management interface has been accessed, a dialogue displays to start the...

  • Page 25

    Installation Guide The first page of the Initial AP Setup Wizard displays the Navigation Panel and Introduction for the configuration activities comprising the access point's initial setup A green checkmark to the left of an item in the Navigation Panel defines the listed task as having its minimum required configuration parameters set correctly.

  • Page 26

    AP6562 Access Point The Introduction screen displays a list of the basic configuration activities supported by the Initial Setup Wizard. 8. Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to the next page listed in the Navigation Panel. Select Back to revert to the previous screen in the Navigation Panel without saving your updates.

  • Page 27

    • Standalone AP -Select this option to deploy this access point as an autonomous fat access point. A Standalone AP isn't managed by a Virtual Controller AP, or adopted by a controller. If designating the access point as a Standalone AP, Motorola Solutions recommends NOTE the access point’s UI be used exclusively to define its device configuration, and not...

  • Page 28

    AP6562 Access Point Select the Automatic controller discovery option to enable the access point to be discovered and adopted using layer 2 settings. If preferring layer 3 adoption, select the Static Controller Configuration option, and define the addresses of the preferred controllers. If using the static method, you’ll also need to define whether the access point receives an IP address using DHCP or if IP...

  • Page 29

    Installation Guide 12. Select an Access Point Mode from the available options. • Router Mode - In Router Mode, the access point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single access point.

  • Page 30

    AP6562 Access Point 14. Set the following DHCP and Static IP Address/Subnet information for the LAN interface: • Use DHCP - Select the checkbox to enable an automatic network address configuration using the access point’s DHCP server. • Static IP Address/Subnet - Enter an IP Address and a subnet for the access point's LAN interface. If Use DHCP is selected, this field is not available.

  • Page 31

    Installation Guide • DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP addresses. If this option is not selected, a primary and secondary DNS resource must be specified. DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible for converting the name into its corresponding IP address, cannot locate the matching IP address.

  • Page 32

    AP6562 Access Point • Enable NAT on the WAN Interface - Select the checkbox to allow traffic to pass between the access point's WAN and LAN interfaces. 17. Select Next. The Initial AP Setup Wizard displays the Radio Configuration screen to define support for the 2.4GHz radio band, 5GHz radio band or to set the radio's functionality as a dedicated sensor.

  • Page 33

    Installation Guide • Channel Mode - Select either Random, Best or Static. Select Random for use with a 802.11an radio. To comply with Dynamic Frequency Selection (DFS) requirements in the European Union, the 802.11an radio uses a randomly selected channel each time the access point is powered on. Select Best to enable the access point to scan non-overlapping channels and listen for beacons from other access points.

  • Page 34

    AP6562 Access Point 20. Set the following parameters for each of the two WLAN configurations available as part of this Initial AP Setup Wizard: • SSID - Enter or modify the Services Set Identification (SSID) associated with the WLAN. The WLAN name is auto-generated using the SSID until changed by the user.

  • Page 35

    Installation Guide 22. Refer to the Username, Password, Description and Actions columns to review credentials of existing RADIUS Server user accounts. Add new accounts or edit the properties of existing accounts as updates are required. 23. Refer to the Add On-Board RADIUS Server Users field to set the following parameters for a user account: •...

  • Page 36

    • Location - Define the location of the access point. The Location parameter acts as a reminder of where the AP is deployed within the Motorola Solutions managed wireless network. • Contact - Specify the contact information for the administrator. The credentials provided should accurately reflect the individual responding to service queries.

  • Page 37

    Installation Guide maximum RF signal strength that can be transmitted. This is a required parameter. • Time Zone - Set the time zone where the access point is deployed. This is a required parameter. The setting should be complimentary with the selected deployment country. 27.

  • Page 38

    Navigational Panel, or use the Back and Next buttons to scroll to the target screen For information on how use a Motorola Solutions RFS Series controller to manage an AP6562 access point, refer to http://supportcentral.motorola.com/support/product/manuals.do.

  • Page 39: Specifications

    Power in (PoE) 802.3at 4.2 AP6562 Internal Antenna Model Physical Specifications An AP6562 internal antenna model access point has the following physical specifications: Dimensions 9.1 in W x 9.8 in H x 2.6 in D 23.1cm W x 24.9cm H x 24.9cm D...

  • Page 40: Ap6562 External Antenna Model Physical Specifications

    AP6562 Access Point 4.4 AP6562 External Antenna Model Power Specifications An AP6562 external antenna model access point has the following power specifications: Operating voltage 36-57 VDC Power in (PoE) 802.3at 4.5 AP6562 External Antenna Model Physical Specifications An AP6562 external antenna model access point has the following physical specifications: Dimensions 9.1 in W x 9.8 in H x 2.6 in D...

  • Page 41: Radio Specifications

    Installation Guide 4.6 Radio Specifications AP6562 model access points have the following radio specifications: Data rates supported 802.11b/g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps 802.11a: 6,9,12,18,24,36,48, and 54Mbps 802.11n: MCS 0-15 up to 300Mbps Network standard 802.11a, 802.11b, 802.11g, 802.11n Wireless medium Direct Sequence Spread Spectrum (DSSS),...

  • Page 42: Regulatory Information

    This device is approved under Motorola Solutions, Inc. This guide applies to MODEL: AP6562 All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following web site: http://supportcentral.motorola.com...

  • Page 43

    Installation Guide The professional installer should utilize the Motorola Antenna Guides 72E-162906-01 at http://www.motorolasolutions.com to ensure a compliant configuration consistent with the FCC Grant and the IC Listing. The transmitter power settings for each of the authorized antennas are contained in the Motorola Antenna Guide.

  • Page 44: Rf Exposure Guidelines, Safety Information, Us And Canada, Power Supply

    Power Supply Use ONLY a LISTED Motorola, Type no. PWRS-14000-148R (12VDC @ 4.16A), direct plug-in power supply, marked Class 2 (IEC60950-1, SELV). This device can be powered from a 802.3at compliant power source which is certified by the appropriate agencies.

  • Page 45: Radio Transmitters

    This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed in the Motorola Antenna Guides 72E-162906-01 at http://www.motorolasolutions.com with the maximum permissible gain and required antenna impedance for each antenna type indicated.

  • Page 46: Statement Of Compliance

    Declarações Regulamentares para AP6562 - Brasil Nota: A marca de certificação se aplica ao Transceptor, modelo AP6562. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

  • Page 47

    Installation Guide Taiwan 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備,限於室內使用 Korea Turkish WEEE Statement of Compliance EEE Yönetmeliğine Uygundur...

  • Page 48

    : http://www.motorola.com/recycling/weee. Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.motorola.com/recycling/weee.

  • Page 49

    Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.motorola.com/recycling/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.motorola.com/recycling/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας...

  • Page 50: Motorola Solutions Support Center

    AP6562 Access Point 6 Motorola Solutions Support Center If you have a problem with your equipment, contact Motorola Solutions Support for your region. Support and issue resolution is provided for products under warranty or that are covered by an Motorola Solutions Support agreement.

  • Page 51

    (ii) means any modifications, enhancements, new versions and new releases of the software provided by Motorola Solutions; and (iii) may contain items of software owned by a third party supplier. The term "Software" does not include any third party software provided under separate license or third party software not licensable under the terms of this Agreement.

  • Page 52

    Software or Documentation to be placed in the public domain; (iv) remove, or in any way alter or obscure, any copyright notice or other notice of Motorola Solutions' proprietary rights; (v) provide, copy, transmit, disclose, divulge or make the Software or Documentation available to, or permit the the Software by any third party or on any machine except as expressly authorized by this Agreement;...

  • Page 53

    Agreement. 5.OWNERSHIP AND TITLE 5.1 Motorola Solutions, its licensors, and its suppliers retain all of their proprietary rights in any form in and to the Software and Documentation, including, but not limited to, all rights in patents, patent applications, inventions, copyrights, trademarks, trade secrets, trade names, and other proprietary rights in or relating to the Software and Documentation.

  • Page 54

    End-User License Agreement. End-User Customer's right to use the Software will continue for the life of the Products with which or for which the Software and Documentation have been provided by Motorola Solutions, unless End-User Customer breaches this End-User License Agreement, in which case this End-User License Agreement and End-User Customer's right to use the Software and Documentation may be terminated immediately by Motorola Solutions.

  • Page 55

    11.4 Waiver. No waiver of a right or remedy of a Party will constitute a waiver of another right or remedy of that Party. 11.5 Assignments. Motorola Solutions may assign any of its rights or sub-contract any of its obligations under this End-User License Agreement or encumber or sell any of its rights in any Software, without prior notice to or consent of End-User Customer.

  • Page 56

    AP6562 Access Point 11.9 Dispute Resolution. Unless End-User Customer is a sovereign governmental entity, any dispute arising from or in connection with this End-User License Agreement shall be submitted to the sole and exclusive forum of the state and federal courts sitting in New Castle County, Delaware (the "Delaware Courts"), and each Party irrevocably submits to the jurisdiction of the Delaware Courts for the litigation of such disputes.

  • Page 57: Ap6562 Access Point China Rohs Compliance

    塑料和聚合物部件 (Plastic and Polymeric Parts) 光学和光学组件 (Optics and Optical Components) 电池 (Batteries) O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以 下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量 要求。 对销售之日的所售产品,本表表示,公司供应链的电子信息产品可能包含这些物质。注意:在所售产品 中可能会也可能不会含有所有所列的部件。 This table was created to comply with China RoHS requirements for Motorola Solutions‘ AP6562 Access Point.

  • Page 58

    AP6562 Access Point...

  • Page 59

    Installation Guide...

  • Page 60

    Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All Rights Reserved.

Comments to this Manuals

Symbols: 0
Latest comments: