Initialization Of B Page Data; (Dcr-Pc120Bt/Pc120E); Modification Of B Page Data; Writing The Network Default Setting Value - Sony Handycam DCR-PC115 Service Manual

DCR-PC115/PC115E/PC120BT/PC120E
1-2-2.

INITIALIZATION OF B PAGE DATA

(DCR-PC120BT/PC120E)

Note1: When reading the B page data, insert a "Memory Stick" into the
"Memory Stick" slot.
Note2: "INITIALIZATION OF B PAGE DATA" should be carried out
upon completion of "INITIALIZATION OF C, D, 8 PAGE DATA".
Switch setting:
POWER ................................................................. MEMORY
1. Initializing the B Page Data
Note: If the B page data has been initialized, the following adjustments
need to be performed again.

1) Modification of B page data

2) Writing the network default setting value

Adjusting page
Adjusting Address
Initializing Method:
Order Page Address Data
1 0 01
2 2 8F
3 2 8F
4 2 8F
5 2 8F
6 5 0E
7 5 01
8 5 00
9
10 5 0E
11 5 02
12 5 01
13 5 00
14 5 02
15 2 0E
16 5 01 FD
17 5 00
18 5 0E
19
B
00 to FF
Procedure
01 Set the data.
02 Set the data, and press PAUSE
button.
03 Set the data, and press PAUSE
button.
02 Set the data, and press PAUSE
button.
00 Set the data, and press PAUSE
button.
00 Set the data.
F3 Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Wait for 3 sec.
Check that the data is "01".
01 Set the data, and press PAUSE
button.
FE Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data.
When the data is "00", proceed
to step 19.
When the data is "FF", proceed
to step 15.
00 Set the data, and press PAUSE
button.
Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data is "01".
Perform "Modification of B Page
Data".
2. Modification of B Page Data
If the B page data has been initialized, change the data of the "Fixed
data-2" address shown in the following tables by manual input.
Preparations:
Order Page Address Data
1 2 8F
2 2 8F
3 2 8F
4 2 8F
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of B Page data:
Order Page Address Data
1 2 00
2 2 01
3. Writing the Network Default Setting Value
Writing method:
Order Page Address Data
1 0 01
2 5 01
3 5 09
4 5 0A
5 5 00
6 5 0E
7 0 01
4. B Page Table
Note: Fixed data-1: Initialized data. (Refer to "1. Initializing the B Page
Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of B Page
Data".)
Address
00 to AF Fixed data-1
B0 Fixed data-2
B1 to FF Fixed data-1
5-12
Procedure
02 Set the data, and press PAUSE
button.
03 Set the data, and press PAUSE
button.
02 Set the data, and press PAUSE
button.
00 Set the data, and press PAUSE
button.
Procedure
29 Set the data.
29 Set the data, and press PAUSE
button.
Procedure
01 Set the data.
E7 Set the data, and press PAUSE
button.
80 Set the data, and press PAUSE
button.
Set the following data, and press
PAUSE button.
03: US model
01: Except US model
01 Set the data, and press PAUSE
button.
Check that the data is "01".
00 Set the data.
Remark
Table. 5-1-5.