Table of Contents
Advertisement
1-2.
INITIALIZATION OF D, E, F, 7 PAGE DATA
1. Initializing the D, E, F, 7 Page Data
Note 1: If "Initializing the D, E, F, 7 Page Data" is performed, all data of
the D page, E page, F page and 7 page will be initialized. (It is
impossible to initialize a single page.)
Note 2: If the D, E, F, 7 page data has been initialized, "Modification of D,
E, F, 7 Page Data" and all adjustments need to be performed again.
Adjusting page
D
Adjusting Address
00 to 85
Adjusting page
F
Adjusting Address
00 to FF
Adjusting page
E
Adjusting Address
00 to FF
Adjusting page
7
Adjusting Address
00 to FF
Initializing Method:
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 6, address: 00, and set data: 51.
3)
Select page: 6, address: 01, set data: 51, and press the PAUSE
button of the adjustment remote commander.
4)
Select page: 6, address: 02, and check that the data is 01.
5)
Select page: 2, address: 00, and set data: 29.
6)
Select page: 2, address: 01, set data: 29, and press the PAUSE
button.
7)
Perform "Modification of D, E, F, 7 Page Data".
2. Modification of D, E, F, 7 Page Data
If the D, E, F, 7 page data has been initialized, change the data of
the "Fixed data-2" address shown in the following tables by manual
input.
Modifying Method:
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of D, E, F, 7 Page
data
1)
Select page: 2, address: 00, and set data: 29.
2)
Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
Note: If the following symptoms occur after completing of the
"Modification of D, E, F, 7 page data", check that the data of the
"Fixed data-2" addresses of D page are same as those of the same
model of the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
3. D Page Table
Note1: Fixed data-1: Initialized data. (Refer to "1. Initializing the D, E, F,
7 Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of D, E, F,
7 Page Data".)
Address
Initial value
00 to 0F
10
00
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
5-9
Remark
Test mode
Fixed data-1
(Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
(Initialized data)
Hide quick links:
Advertisement
Table of Contents
