Sony Handycam DCR-PC115 Service Manual page 126

• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by
Adjustment
Adjustment
Section
Initialization of Initialization of C, D, 8 page data
B,C,D,E,F,7,8 Initialization of B page data
page data Initialization of E, F, 7 page data
40.5/54MHz origin oscillation adj.
MR adj.
HALL adj.
MAX GAIN adj.
CCD output 2ch matching adj.
Flange back adj.
Color reproduction adj.
Camera AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj.
Steady shot check
Strobe light level adj.
Strobe white balance adj. & check
AF laser output adj.
AF laser optical axis adj.
VCO adj.
Backlight adj.
Color EVF Bright adj.
Contrast adj.
White balance adj.
VCO adj.
Bright adj.
Black limit adj.
PSIG gray adj.
LCD
Contrast adj.
Center level adj.
V COM adj.
White balance adj.
System control Serial No. input
CAP FG duty adj.
Switching position adj.
Servo & RF AGC center level adj.
APC & AEQ adj.
PLL fo & LPF fo adj.
Chroma BPF fo adj.
Video S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Mechanism Tape path adj.
Board
replacement
*1
*1
z
*1
*1
*1
*1
z z
z z
z z
z z
z z
z z
z z
z z
Table. 5-1-1 (2).
DCR-PC115/PC115E/PC120BT/PC120E
z in the following table.
Note2: When the repair is finished, confirm the
EEPROM
replacement
1. Shoot the all black subject (Attach the lens cap and
shoot), and confirm that a vertical line is not
displayed in the center of the screen, and that there
is no difference in left-right brightness level of the
screen.
2. Shoot a subject of low light, and confirm that a
vertical line is not displayed in the center of the
screen, and that there is no difference in left-right
brightness level of the screen.
3. Shoot a subject of normal light, and confirm that a
vertical line is not displayed in the center of the
screen, and that there is no difference in left-right
brightness level of the screen.
When the above symptom occurs, perform the whole
process of "CCD Output 2ch Matching Adjustment".
Note3: DCR-PC120BT/PC120E only.
When the BT-003 board is replaced, perform following
procedure and check that the "Self Information" is
displayed correctly.
1) Set the POWER switch to MEMORY.
z z
2) Press NETWORK button.
z z
3) Select "Setup" of the network menu, then
z z
z z
4) Select "Bluetooth Setup", then execute it.
z z z
5) Select "Info.", then execute it.
z z z
6) Check that the following information is
z z z
z z
z z z
z z
z z z
z z z
Note4: When replacing the VC-270 board, before
z z z
z z z z
z z z
z z z
z z z
z z z
Note5: When replacing the HI microprocessor, Input
z z z
z z z
z z z
z z z
z *1: Perform this adjustment when replace the
z
z
z
z
z
z
z
z z
z z z
z z z
z z z
z z z
z z z
z z
z z
z z
5-3
following items.
execute it.
displayed.
Name SONY-PC120
Address 08:00:46:XX:XX:XX
and after replacing, perform "Writing the
Network Default Setting Value" and initialize
the personal network information (Mail
address, bookmark etc.).
(DCR-PC120BT/PC120E only)
(Refer to "1-2-2. INITIALIZATION OF B
PAGE DATA".)
data corresponding to the microprocessor's
version to page: D, address: DC and DD.
(Refer to Table 5-1-3. "D PAGE DATA".)
CCD imager (IC101) and this board at the
same time.