Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB740
Summary of Contents for Gage Bilt GB740
- Page 1 GB740 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A. e-mail: solutions@gagebilt.com / www.gagebilt.com...
-
Page 2: Table Of Contents
Description Page Warnings ............................... 3 Principle of Operation .......................... 4 How to use the GB740 .......................... 5 Description, Operation and Maintenance ................... 6 Filling, Bleeding and Troubleshooting....................7 Overhaul, Disassembly and Parts Lists ................... 8-9 DEXRON ® III Oil Safety Data ......................10 Nose Assembly Selection Chart ...................... -
Page 3: Warnings
81.5 DBA. Therefore, it daily basis for damage or wear. Any repair should is required where prolonged use, hearing be done by qualified personnel trained on Gage Bilt protection be used. procedures. WARNING... -
Page 4: Principle Of Operation
PRINCIPLE OF OPERATION When the trigger is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool causing the air to be redirected. The air is directed to the top of the air piston, moving it in a downward direction. -
Page 5: How To Use The Gb740
HOW TO USE THE GB740 WARNING: OPERATOR MUST READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS. WARNING: IT IS REQUIRED THAT EYE PROTECTION AND HEARING PROTECTION BE WORN DURING OPERATION. WARNING: DO NOT PULL RIVET IN THE AIR. PERSONAL INJURY FROM FASTENER EJECTING MAY OCCUR. -
Page 6: Description, Operation And Maintenance
The GB740 riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 psi, the GB740 does not exceed 81.5 db (A) and consumes 3 cfm at 20 cycles a minute. -
Page 7: Filling, Bleeding And Troubleshooting
FILLING AND BLEEDING TOOL WARNING DO NOT CYCLE TOOL WITHOUT AIR BLEEDER, OR THE SCREW AND STAT-O-SEAL, INSTALLED IN TOOL HEAD. SEVERE PERSONAL INJURY MAY RESULT. CAUTION BEFORE FILLING HANDLE, AIR PISTON SHOULD BE ALL THE WAY DOWN. To replace a small amount of oil in the tool, attach the air bleeder and connect tool to air line. Cycle a number of times. Disconnect air, remove the air bleeder, and reinstall the cap screw. -
Page 8: Overhaul, Disassembly And Parts Lists
OVERHAUL The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. It is recommended that tool kit (GB740TK) be used to facilitate overhaul. -
Page 9: Air Valve
HANDLE To inspect air cylinder bore, remove base cover (744124) and o’ring (S12). Any further disassembly will require removal of the head assembly first. For complete disassembly, start by removing parts (744124) and (S12). Next, holding tool upright, remove four button -head cap screws (402479). -
Page 10: Dexron® Iii Oil Safety Data
DEXRON® III OIL SAFETY DATA FIRST AID Skin: Wash thoroughly with soap and water as soon as possible. Casual contact requires no immediate attention. If irritation develops, consult a physician. Ingestion: Seek medical attention immediately. DO NOT INDUCE VOMITING. Eyes: Flush with copious amounts of water. If irritation develops, consult a physician. Inhalation: No significant adverse health effects are expected to occur on short term exposure. -
Page 11: Nose Assembly Selection Chart
BACS53B1EA1/2 CHERRYLOCK® IS A REGISTERED TRADEM ARK OF CHERRY AEROSPACE. M ONEL® IS A REGISTERED TRADEM ARK OF SPECIAL M ETAL CORPORATIONS. GAGE BILT CERTIFIES THE GB740 WILL INSTALL THE ABOVE FASTENERS 1) REQUIRES 740715 ADAPTER. 2) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN 1 PULL. -
Page 12: Eu Conformity And Warranty
WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING STANDARDS AND DIRECTIVES. EN12100-1 & EN12100-2 EN13849 EN792-1:2000+A1 COUNCIL DIRECTIVE: MACHINE DIRECTIVE 2006/42/EC EQUIPMENT DESCRIPTION: GB740 FASTENER INSTALLATION TOOLS MANUFACTURER: GAGE BILT Inc. SIGNATURE: NAME: BRIAN LEIGH PRODUCT MANAGER CLINTON TWP., MI U.S.A.