Using The Snow Thrower - Stiga 966 D Instructions For Use Manual

Hide thumbs Also See for 966 D:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 65
EN
4.21 HANDLE HEATING (6)
The machine is equipped with electrical handle heating. To
activate the heating, set the switch in the desired position:
Forwards - Light heating
Middle - No heating
Backwards - Full heating
The heating can be activated when the motor is running only.
4.22 HEADLAMP (15)
The headlamp is always activated when the motor is running.
4.23 CHUTE CLEARING TOOL (10)
The chute clearing tool is located in a holder on top of the
auger housing. The chute clearing tool must always be used
when cleaning the discharge chute and augur.
Always stop the engine before clearing the chute.
Never clear the snow discharge chute with your
hand. Risk of serious injury.
4.24 ADJUSTMENT SWITCH (23) (1381)
Changes the direction of the discharged snow.
Forwards - Chute turns to the left
Backwards - Chute turns to the right.

5 USING THE SNOW THROWER

5.1
GENERAL
Never start the engine until all the above measures under
ASSEMBLY have been carried out.
Never use the snow thrower without first reading
and understanding the instructions and all the
warning and instruction stickers on the machine.
Always use protective goggles or a visor during
use, maintenance and service.
5.2
BEFORE STARTING
Some snow throwers are delivered without oil in the engine.
Fill the engine with oil before using. The oil is supplied in a
separate bottle.
Do not start the engine until filled with oil. The
engine can be seriously damaged without oil.
1. Place the machine on a level floor.
2. Loosen the dipstick and fill with oil up to the FULL mark
(fig. 9).
3. Use good quality oil marked A.P.I service SF, SG or SH.
Use SAE 5W30 - 10W40 oil.
4. The crankcase holds: 0.8 litres.
Always check the oil level before using. The snow thrower
must stand on level ground when checking.
68
ENGLISH
5.3
FILL UP THE PETROL TANK
Always use lead-free petrol. Oil-mixed 2-stroke petrol must
not be used.
NOTE! Bear in mind that ordinary lead-free petrol is
perishable; do not purchase more petrol than can be used
within thirty days.
Environmental petrol can be used, i.e. alkylate petrol. This
type of petrol has a composition that is less harmful for
people and nature.
Petrol is highly inflammable. Always store fuel in
containers that are made especially for this
purpose.
Store the petrol in a cool, well ventilated place –
not in the house. Store the petrol well out of reach
for children.
Only fill or top up with petrol outdoors, and never
smoke when filling or topping up. Fill with fuel
before starting the engine. Never remove the filler
cap or fill with petrol while the engine is running
or still warm.
Do not fill the petrol tank right to the top. After filling, screw
the filler cap on tightly and wipe up any spilt petrol.
5.4
STARTING THE ENGINE (WITHOUT
ELECTRICAL START)
Do not touch engine components because they are
warm during use. Risk of burn injuries.
Never run the machine indoors. The exhaust
fumes contain carbon monoxide, a very toxic gas.
1. Make sure the driving and auger clutch levers are
disengaged (fig. 1).
2. Push the throttle to position
3. Put in the ignition key. Ensure it clicks tight. Do not turn
the key!
4. Turn the choke to position
not need the choke.
5. Press the rubber primer-start 2 or 3 times. Make sure the
hole is covered when pressing the primer-start (fig. 10).
Note: Do not use this function when the engine is warm.
6. Pull on the starter cord until you feel resistance. Start the
engine with a sharp pull.
7. When the engine starts, turn the choke anti-clockwise
until it is fully open.
5.5
STARTING THE ENGINE (WITH ELECTRICAL
START)
Do not touch engine components because they are
warm during use. Risk of burn injuries.
Never run the machine indoors. The exhaust
fumes contain carbon monoxide, a very toxic gas.
1. Attach the connecting cable to an earthed extension lead.
Then connect the extension lead to a 220/230 volt earthed
socket.
2. Make sure the driving and auger clutch levers are
disengaged (fig. 1).
3. Push the throttle to position
4. Put in the ignition key. Ensure it clicks tight. Do not turn
the key!
.
. Note: A warm engine does
.

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

1171 hst1381 hst

Table of Contents