Assembly - ICON weider 8515 WESY87150 User Manual

WEIGHT RESISTANCE CHART
This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6.5 lb. top weight. The
other numbers refer to the 12.5 lb. weight plates. Weight resistance shown for the butterfly arm station is for
each butterfly arm.
WEIGHT PRESS ARM BUTTERFLY ARM
PLATES (lbs.) (lbs.)
Top 20 10
1 45 22
2 70 33
3 99 42
4 128 48
5 153 60
6 184 69
Note: 1 kg = 2,2 lbs
The actual resistance at each weight station may vary due to differences in individual weight plates, as
well as friction between the cables, pulleys, and weight guides.
LEG LEVER HIGH PULLEY LOW PULLEY
(lbs.) (lbs.) (lbs.)
15 14 24
36 28 54
54 44 82
75 60 115
96 72 147
115 90 175
137 103 209
20

ASSEMBLY

Before beginning assembly, carefully read the
following information and instructions:
¥ Place all parts of the WEIDER 8515 in a cleared
area and remove the packing materials; do not
dispose of the packing materials until assembly is
completed.
¥ The assembly is divided into four stages: 1)
frame assembly, 2) press and butterfly arm
assembly, 3) cable and pulley assembly, and 4)
seat and backrest assembly. The hardware for
each stage is packaged separately.
¥ Wait until you begin each assembly stage to open
that parts bag.
¥ For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the centre of this manual.
Note: Some small parts may have been pre-
attached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.
1. Before beginning assembly, be sure that
you have read and understand the infor-
mation in the box above.
Press a 2Ó Square Outer Cap (51) onto each
end of the Stabiliser (5). Press a 2Ó Square
Inner Cap (27) into the end of the Base (4).
Turn the Stabiliser (5) so that the long side is
positioned as shown.
Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14)
up through the Stabiliser (5). Insert a 5/16Ó x
2 1/2Ó Carriage Bolt (1) up through the
remaining hole in the Stabiliser. Insert two
5/16Ó x 2 1/2Ó Carriage Bolts (1) up through
the Base (4).
Slide the indicated end of the Base (4) onto
the 5/16Ó x 2 3/4Ó Carriage Bolts (14) in the
Stabiliser (5). Slide the Rear Upright (56)
onto the Carriage Bolts. The high side of
the bracket on the Rear Upright must be
on the side shown. Hand tighten a 5/16Ó
Nylon Locknut (3) onto each Carriage Bolt.
Do not tighten the Nylon Locknuts yet.
Wet the handles on the Rear Upright (56)
with soapy water. Slide a Hand Grip (31)
onto each handle.
¥ As you assemble the WEIDER 8515, be sure that
all parts are oriented as shown in the drawings.
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
¥ Two (2) adjustable spanners
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ One (1) rubber mallet
¥ Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end spanners, or a set of ratchet spanners.
1
High Side of
Bracket
Handles
31
56
51
3
Long Side
5
4
14
51
1
1
5
27