Before You Begin - ICON weider 8515 WESY87150 User Manual

BEFORE YOU BEGIN

Thank you for selecting the versatile WEIDER ¨ 8515
Home Gym System. The WEIDER ¨ 8515 offers a
selection of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
WEIDER ¨ 8515 will help you to achieve the specific
results you want.
For your benefit, read this manual carefully before
using the WEIDER ¨ 8515 Home Gym System. If you
ASSEMBLED
DIMENSIONS:
Height: 74 in.
Width: 40 in.
Length: 53 in.
Butterfly Arms
Backrest
Press Arm
Seat
Leg Lever
Foot Plate
have additional questions, please call our Customer
Service Department at 0345-089009. To help us assist
you, please note the product model number and serial
number before calling. The model number is
WESY87150. The serial number can be found on a
decal attached to the WEIDER 8515 (see the front
¨
cover of this manual).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labelled.
High Pulley Station
Lat Bar
Resistance
Cylinders
Stepper Pedals
Weight Pin
Weight Stack
Low Pulley Station
4
TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts often and replace any worn parts immediately. The home gym system can be
cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the home
gym system, can stretch slightly when it is first used.
If there is slack in the cables before resistance is felt,
the cables should be tightened. IMPORTANT: The
Weight Pin (26) must be inserted under the middle
Weight (25) before the cables can be tightened.
Slack can be removed from the cables three different
ways:
¥ See drawing 1. Tighten the 1/4Ó Nylon Locknut (2)
at the end of the Long Cable (23). To do this you
may need to remove the Small ÒUÓ -Bracket (67)
from the Weight Tube (63). Make sure that the
cables are not too tight, or the Top Weight (76)
will be lifted off the weight stack.
¥ See drawing 2. Tighten the 1/4Ó Nylon Locknut (2)
at the end of the Short Cable (58). To do this you
may need to remove the 3 1/2Ó Pulley (15) and
the Pulley Covers (89) from the Long ÒUÓ-Bracket
(57). Make sure that the cables are not too tight,
or the Top Weight (76) will be lifted off the weight
stack.
¥ See drawing 2. Move the 3 1/2Ó Pulley (15) and
the Pulley Covers (89) to the other hole in the
Long ÒUÓ-Bracket (57). Remove the 3/8Ó Nylon
Locknut (21) and the 3/8Ó x 2Ó Bolt (12) from the
Pulley, and the Long ÒUÓ-Bracket. Re-attach the
Pulley and Pulley Covers. Be sure that the Cable
and Pulley move smoothly.
Note: Inspect all cables before each use. If a cable tends to slip off the pulleys often, the cable may have
become twisted. Remove the cable and re-install it.
If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
Replace all cables every two years.
1
23
67
2
76
63
25
26
2
23
15
89
57
12
21
58
2
21