Front Upright (42 - ICON weider 8515 WESY87150 User Manual

18. Route the Long Cable (23) around the 3 1/2Ó
Pulley (15) attached to the bracket on the Top
Frame (55). Tighten the 3/8Ó x 2Ó Bolt (12)
and the 3/8Ó Nylon Locknut (21). (Note: This
Pulley is pre-assembled. It has been
shown disassembled for easy part identifi-
cation.) Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
19. Remove the 3 1/2Ó Low Pulley (88) from the
Press Frame (17). Re-attach the Pulley with a
5/8Ó x 9/16Ó Spacer (73) between the Pulley
and the Press Frame. Finger tighten the
3/8Ó Nylon Locknut (21).
Route the Short Cable (58) under the 3 1/2Ó
Low Pulley (88) attached to the lower hole in
the Press Frame (17). Be sure that the end
of the Cable with the ball is on the indicat-
ed side of the Press Frame and that the
Cable is between the Pulley and the cross-
bar on the Press Frame. Tighten the 3/8Ó
Nylon Locknut (21).
If the indicated 3 1/2Ó Pulley (15) is pre-
attached to the Front Upright (42), remove it.
Route the Short Cable (58) around the Pulley.
Attach the Pulley and two Pulley Covers (89)
to the lower hole in the Front Upright with the
3/8Ó Nylon Jam Nut (92), the 3/8Ó Flat Washer
(9) and the 3/8Ó x 3 3/4Ó Bolt (71).
12
18
23
12
Bracket
55
15
21
19
89
71
15
9
9
58
42
73
Ball
92
88
21
Crossbar
17
20. Route the Short Cable (58) around the 3 1/2Ó
Pulley (15) attached to the upper hole in the
Press Frame (17). Be sure that the Cable
Trap (66) is in the Ò3 oÕclockÓ position and
that the Cable is routed around the Pulley
as shown. Tighten the 3/8Ó Nylon Locknut
(21) and the 3/8Ó x 3 3/4Ó Bolt (not shown).
If the indicated 3 1/2Ó Pulley (15) is pre-
attached to the Front Upright (42), remove it.
Route the Short Cable (58) around the 3 1/2Ó
Pulley. Attach the Pulley and two Pulley
Covers (89) to the upper hole in the Front
Upright with the 3/8Ó Nylon Jam Nut (92), the
3/8Ó Flat Washer (9) and the 3/8Ó x 3 3/4Ó Bolt
(71). Be sure that the Cable is routed
around the Pulley as shown.
21. Attach the end of the Short Cable (58) to the
Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon Lock-
nut (2) and a 1/4Ó Flat Washer (10). Do not
completely tighten the Nylon Locknut. It
should be threaded onto the end of the
Cable so only a couple of threads are
showing above the Nylon Locknut, as
shown in the inset drawing.
13
20
42
58
89
71
15
21
66
12
9 3
6
92
9
17
21
2
57
10
58
67
2
10
58