Troubleshooting; Ec Declaration Of Conformity - Black & Decker GL67 Instruction Manual

Repeat the above procedure for the second cutting line on
x
the lower section of the spool. Park the line in the unused
slots (23).
Proceed as described above to fit the spool on the tool.
x
Do not forget to release the cutting line from the parking
slots (23).
Warning! Only use the appropriate type of Black & Decker
cutting line. Ensure that cutting line is present in both sections
of the spool (fig. K).

Troubleshooting

If your tool seems not to operate properly, follow the instructions
below. If this does not solve the problem, please contact your
local Black & Decker repair agent.
Warning! Before proceeding, switch off and unplug the tool.
Tool runs slowly
Check that the spool housing can rotate freely.
x
Carefully clean it if necessary.
Check that the cutting line does not protrude more than
x
11 cm from the spool housing. If it does, cut it off so that
it just reaches the line trimming blade.
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover from
x
the housing.
Pull the cutting line until it protrudes 11 cm from the
x
housing. If insufficient cutting line is left on the spool,
install a new spool of cutting line as instructed above.
Align the tabs on the spool cover with the cut outs in the
x
housing.
Push the cover onto the housing until it snaps securely
x
into place.
If the cutting line protrudes beyond the trimming blade,
x
cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool cover and housing.
x
Remove the spool and check if the lever can move freely.
x
Remove the spool and unwind the cutting line, then wind
x
it on neatly again as described above. Replace the spool
as instructed.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge.
To take advantage of this service please return your
product to any authorised repair agent who will
collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Technical data
Power input
No load speed
Weight

EC declaration of conformity

Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 60335, EN 55014,
EN 61000, 2000/14/EC, Lawn trimmer, L < 50 cm
Annex VIII, No. 0086
B.S.I., HP2 4SQ, United Kingdom
Level of sound pressure, measured according to 2000/14/EC:
L (sound pressure): 81 dB(A), L
pA
L (guaranteed) 96 dB(A)
WA
Hand/arm weighted vibration, measured according to EN 786:
< 2.5 m/s
Kevin Hewitt
Spennymoor, County Durham DL16 6JG,
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase,
ENGLISH
GL675
W 400
-1
min 9.500
kg 2.8
GL675
(acoustic power) 95 dB(A),
WA
2
Director of Consumer Engineering
United Kingdom
01-10-2002
7