Troubleshooting - Pro-Form 470 cx User Manual

ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, lubricant may be transferred to the top of the walking 1
L
belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own phillips screwdriver
ters , and adjustable spanner
For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags,
check to see if the part has been preattached.
1/4" x 1" Bolt
5/16" x 1" Bolt
3/4" Screw (33)–5
(88)–8
(113)–4
5/16" x 3 1/2" Bolt (121)–2
1. With the help of a second person, carefully raise the
treadmill to the upright position as shown.
Insert one of the Extension Legs (86) into the treadmill as
shown. Make sure that the Extension Leg is turned so
the Base Pad (125) is underneath it. If necessary, tip the
Uprights (96) forward as you insert the Extension Leg.
Insert the other Extension Leg (not shown) in the same
way.
,wire cut-
.
1" Tek Screw 1/2" Screw (52)–1
(123)–4
1/4" Star Washer
5/16" Washer (128)–2
(87)–8
1
96
86
125
6

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call the telephone number on the front
cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 10.) If an ex-
tension cord is needed, use only a 3-conductor, 1 mm
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
frame near the power cord. Make sure that the switch
is in the "on" position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the "on" position.
e. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. With the help of another person,
carefully tip the Uprights (96) down as shown.
Remove the three 3/4" Screws (33). Note: A phillips
screwdriver with a shaft at least a 5" long is required.
With the help of another person, carefully raise the
Uprights (96) as shown. Carefully pivot the Hood (64)
off.
2 (14-gauge) cord that is no longer than 1.5
c
Tripped Reset
d
On
Position
a
33
96
96
64
23