Ryobi RAP200 User Manual page 12

GB
FR DE ES
OPERATION
„ Set return tube over waste container to flush out
waste material.
„ Turn prime/spray lever to PRIME.
„ Turn HIGH/LOW pressure control to LOW pressure.
„ Plug in the paint station.
„ Turn ON/OFF switch ON.
„ When material begins to flow through return tube set
return tube into paint container and clip to intake tube.
„ Point pistol-grip sprayer (without guard and spray tip
in place) into waste container.
„ Turn prime/spray lever to SPRAY.
„ Unlock sprayer trigger.
„ Turn HIGH/LOW pressure control from LOW to HIGH
until pump starts.
„ Spray into waste container until all air, water, cleaning
fluid is expelled and only paint comes out.
NOTE: When the motor stops, this indicates that the
pump and hoses are under pressure. If the motor
continues to run, re-prime by turning the prime/spray
lever to PRIME.
„ Turn lock-off thumbscrew counterclockwise to lock
sprayer trigger.
„ Turn ON/OFF switch OFF.
„ Replace nozzle tip guard and reversible spray tip onto
pistol-grip sprayer.
„ Unit is ready to spray.
SELECTING A SPRAY TIP
See Figure 12.
Spray tips come in a variety of hole sizes and fan widths.
Your unit includes two reversible spray tips with a
hole size of 0.4 cm that will work for a wide variety of
applications. The 415 spray tip has a fan width of 20.3 -
30.5 cm. The 515 spray tip has a fan width of 25.4 - 30.5
cm.
HOLE SIZE: Spray tip hole size determines the flow
rate, that is the amount of paint that is discharged from
sprayer.
A larger hole size is best for thicker materials. A smaller
hole size is best for thinner materials.
FAN SIZE: Fan width determines the size of the spray
pattern when sprayer is held approximately 30.5 cm. from
surface to be painted.
A narrow fan width will provide thicker coverage of
material and is better suited for small, tight areas.
A wide fan width will give thinner coverage of material
and provide better coverage on large, broad areas.
SPRAY TIP NUMBERS: When selecting a spray tip,
the last three numbers of the spray tip number contains
IT NL PT DK SE FI NO RU PL CZ
English
information on hole size and fan width.
For example if the spray tip number is 1415, the 4, when
doubled is the approximate fan width of paint when
applied 30.5 cm from surface. The last two numbers, 15,
refer to the hole size in inches. In this case 0.4 cm.
Tip
hole
size
0.011
0.013
0.015
0.017
0.019
0.021
SPRAY TIP WEAR: It is important to replace or spray
tips when they become worn. A worn spray tip will cause
uneven application and finish of material. Over time the
spray tip hole size increases and the width of the fan
spray decreases.
When using water based paint, spray tips need to be
replaced between 56.78 and 151.42 liter. For oil based
materials, replace spray tips after 132.49 to 227.12 liter
of use.
To increase the life of your spray tips, use the lowest
pressure setting needed to apply an even coating of
materia.
SPRAYING
See Figure 13.
„ Ensure surface to be painted is free of dust, dirt, and
grease.
„ Mask or cover any areas not intended to be painted
or stained. Be aware of wind that may cause your
paint or stain to spray into areas not desired. Always
use drop cloths or other cover to protect areas that
are not intended to be painted or stained.
„ Select spray tip and seat securely into nozzle tip
guard. Arrow on spray tip should face direction of
spray.
„ Plug in the paint station.
„ Prime unit. Follow Set Up and Priming instructions.
„ Turn ON/OFF switch ON.
„ Turn prime/spray lever to SPRAY.
„ Turn HIGH/LOW pressure control clockwise to
SPRAY icon (HIGH pressure). Pressure can be
adjusted to reach desired spray pattern and coverage.
6
HU RO LV LT EE
Coatings
Light Medium
Stains Enamels Primers
•
• •
• •
•
•
HR SI SK GR TR
Heavy
Interior
Exterior
Paints
Paints
•
• •
• •
•