Sharp AR-M450 Service Manual page 64

Code
Main Sub
22 11 Used to check the use frequency of FAX. (send/receive)
(Only when FAX is installed.)
12 Used to check the misfeed position and the number of misfeed
at that position. (If the number of misfeed is considerably great,
the machine must be repaired.)
13 Used to display the process cartridge data.
19 Used to display the scanner mode counter.
24 1 Used to clear the misfeed counter, misfeed history, trouble
counter, and trouble history. (After completion of maintenance,
these counters must be cleared.)
2 Used to clear the number of use (print quantity) of each paper
feed section.
3 Used to clear the number of use of the staple, ADF, RADF, SPF,
DSPF, and the scanner (reading) unit.
4 Used to reset the maintenance counter.
5 Used to reset the developer counter.
(The developer counter of the DV unit installed is reset.)
6 Used to reset the copy counter.
7 Used to clear the OPC drum counter and the toner cartridge
counter. (Perform when the OPC drum is replaced.)
9 Used to clear the printer print counter. (After completion of
maintenance, this counter must be cleared.)
10 Used to clear the FAX counter. (After completion of
maintenance, this counter must be cleared.)
(Only when FAX is installed.)
11 Used to reset the drum rotation time, toner motor rotation time,
and developer rotation time counters.
The developer counter of the DV unit installed is reset.
15 Used to clear each counter in the scanner mode.
25 1 Used to check the operations of the main drive section
(excluding the scanner (reading) section) and the toner density
sensor. (The toner density sensor output can be monitored.)
2 Used to initialize the toner density when replacing developer.
(Auto adjustment)
26 3 Used to set the specification mode of the auditor. Setup must
be made according to the use condition of the auditor.
5 Used to set the count mode of the total counter and the
maintenance counter.
6 Used to set the specification according to the destination.
10 Used to set the trial mode of the network scanner.
18 Used to set Enable/Disable of toner save operation.
(This simulation is enabled only in Japan and UK versions.
(Depends on SIM 26-6 (Destination) setup).
For the other destinations, user program P22 allows to make
the similar setup.)
30 Used to set the operation mode conforming to the CE mark
(Europe standards).
(For flickers when driving the fusing heater lamp.)
35 Used to set whether the trouble history of SIM 22-4 is displayed
as one-time trouble or continuous troubles when two or more
number of a same trouble occurred.
38 Used to stop printing when developer life is expired.
Function (Content)
AR-M350 SIMULATIONS 10-3
Purpose
Adjustment, setup, FAX
operation data output,
check (display)
Adjustment, setup, DSPF
operation data output,
check (display)
Adjustment, setup,
operation data output,
check (display)
Adjustment, setup,
operation data output,
check (display)
Data clear
Data clear Paper feed
Data clear
Data clear
Data clear Process (OPC drum,
developing, transfer,
cleaning)
Data clear
Data clear Process (OPC drum,
developing, transfer,
cleaning)
Data clear Printer
Data clear FAX
Data clear Process (OPC drum,
developing, transfer,
cleaning)
Data clear
Operation test, check Drive
Setup Process (OPC drum,
developing, transfer,
cleaning)
Setup Auditor
Setup
Setup
Setup
Setup
Setup
Setup
Setup Other
Section Item
Data
Trouble Misfeed
Counter
Counter
Counter
Counter
Counter
Counter
Counter Developer
(DV unit)
Counter Copy
Counter OPC drum
Counter Printer
Counter
Counter Developer
(DV unit)
Counter
Operation
Spec
Spec Counter
Spec Destination
Operation
Spec Operation
mode
(Common
operation)
Spec Operation
mode
(Common
operation)
Spec
Operation