Sharp AR-M450 Service Manual page 112

50-7
Purpose Adjustment
Function (Content) Copy lead edge adjustment (Simple method)
(DSPF)
Section
Item Picture quality
Operation/Procedure Perform the SPF copy lead edge adjustment.
(Simple method)
1) The current set value is highlighted on the
right of each item. In this screen, be sure to
select "1: COPY START." (Set value: 1)
2) Enter the correction value with 10 digit key
pad.
Press P to store the set value.
3) Press START to start copying and store the
set value. (Display value: 1)
4) Select a paper feed tray. (Set value 2)
5) Set the scan magnification ratio. (Set value: 3)
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS START.
0. TRAY SELECT 1. COPY START
1
200
2. MAGNIFICATION
50 160
3. L4 4.L5
5. IMAGE LOSS(LEAD)SIDE1
6. IMAGE LOSS(SIDE)SIDE1
7. IMAGE LOSS(LEAD)SIDE2
8. IMAGE LOSS(SIDE)SIDE2
0
9. REAR LOSS SIDE1
Select other than 0 - 2,
and press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-999, AND PRESS
START.
3. L4
Select 1, and
Press [START] key.
press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
Select 0, and
press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
(ABOVE+10: DUPLEX MODE)
Select 2, and
press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
15
20
15
20
0
10. REAR LOSS SIDE2
Press [CUSTOM SETTING] key.
50
Press [CUSTOM SETTING] key.
Or copying is terminated.
Press [START] key or
press [CUSTOME SETTING] key.
1
Press [START] key or
press [CUSTOME SETTING] key.
100
AR-M350 SIMULATIONS 10-51
<List of set values 1>
0 TRAY SELECT
1 COPY START
2 MAGNIFICATION Print magnification ratio
3 L4
4 L5
5 IMAGE LOSS
(LEAD) SIDE 1
6 IMAGE LOSS
(SIDE) SIDE 1
7 IMAGE LOSS
(LEAD) SIDE 2
8 IMAGE LOSS
(SIDE) SIDE 2
2
9 REAR LOSS
SIDE1
10 REAR LOSS
SIDE2
<List of display values 1>
Normal display
ERROR display
<List of set values 2>
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 Manual feed
<List of set values 3>
Set range 25 - 200%
Defauult Set range
Paper feed tray selection
Copy start (Initial value)
200
setup (25 - 400%)
Distance from the front lead
edge of copy image to the
scale of 10mm.
(SPF: 200%)
Distance from the back lead
edge of copy image to the
scale of 10mm.
(SPF: 200%)
Front lead edge image loss 15
set value
Front side image loss set 20
value
Back lead edge image loss 15
set value
Back side image loss set 20
value
Front rear edge image loss 0
set value
Back rear edge image loss 0
set value
NOW COPYING
Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
11 TRAY1 with Duplex
12 TRAY2 with Duplex
13 TRAY3 with Duplex
14 TRAY4 with Duplex
15 Manual feed with Duplex
- 1 ~ 5
- -
25 ~ 200
0 ~ 999
-
0 ~ 999
-
0 ~ 99
0 ~ 99
0 ~ 99
0 ~ 99
0 ~ 20
0 ~ 20