Download
Share
Print this page
UWE SAC Series Operation Manual
  1. Manuals
  2. Brands
  3. UWE Manuals
  4. Scales
  5. SAC Series
  6. Operation manual

UWE SAC Series Operation Manual

Triple-interval high precision counting scale
Hide thumbs

Advertisement

Quick Links

Enlarged version
SAC SERIES
TRIPLE-INTERVAL HIGH PRECISION
COUNTING SCALE
OPERATION MANUAL
PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT
TO OPERATE THE SCALE
Specifications subject to change without prior notice
December 2001
CONTENTS

Advertisement

loading
Need help?

Need help?

Do you have a question about the SAC Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UWE SAC Series

Summary of Contents for UWE SAC Series

  • Page 1: Table Of Contents

    CONTENTS 1. INSTALLAT ION SAC SERIES TRIPLE-INTERVAL HIGH PRECISION 2. SPECIFICATIONS COUNTING SCALE 3. KEYBOARDS, PANEL LAYOUT AND DESCRIPTION OPERATION MANUAL 4. SCALE SETUP 5. INSTRUCTION FOR USE PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 6.

  • Page 2: Installation

    1. INSTALLATION RETAIN packing materials future transportation purposes. CAUTION: a. This is a precision measuring device, handle with CAUTION: extreme care. In some countries, this unit is required by law to be b. Allow 2 minutes for warm up before operating. sealed (or stamped) and bearing a serial number.

  • Page 3: Specifications

    2. SPECIFICATIONS 3. KEYBOARDS & PANEL LAYOUT AND DESCRIPTION 2.1 GENERAL SPECIFICATIONS Model No. SAC-7.5C 1500g/0.1g 3000g/0.2g 7500g/0.5g SAC-15C 3000g/0.2g 7500g/0.5g 15000g/1g SAC-30C 7500g/0.5g 15000g/1g 30000g/2g SAC-60C 15000g/1g 30000g/2g 60000g/5g Platter 230 x 345mm All Stainless Steel Size Power Built-in Rechargeable or Power Adaptor Source Operation C(32...
  • Page 4 KEYS DESCRIPTION 9. M+ KEY 1. ON/ZERO KEY Press this key to add current total count to memory. Press this key to turn scale on or set weight to zero. Note: When the WEIGHT PANEL shows a negative value, the Refer to SPECIFICATIONS for maximum zero range.

  • Page 5: Scale Setup

    4. SCALE SETUP 15. LOW UNIT WEIGHT INDICATOR An arrow will appear and point at this indicator when 4.1 PLACE THE SCALE the unit piece weight applied/detected is less than the recommended minimum piece weight as listed on 2.2. Place this unit on a hard and strong surface, where is free from RF interference, vibration, fire, airflow, 16.
  • Page 6 a. Refer to the 4.4.1 on how to enter F2 4.3.2 Turn backlight on: - Without Power Saving Mode a. Turn scale on b. Press @WT/SET b. Press and hold 2 c. All display segments will be lighted up c. Backlight is turned on d.

  • Page 7: Instructions For Use

    5.3 PLACE A LOAD 5. INSTRUCTIONS FOR USE Before using, allow 2 minutes for warm up. Always place load onto platter gently. Shock/excessive force may cause irrecoverable damage 5.1 ZERO THE WEIGHT DISPLAYED WHEN UNLOADED to the weight sensor inside. It is a good practice to If ZERO INDICATOR does not appear when the unit is not remove all loads from platter immediately after weighed.
  • Page 8 5.6 AUTO PIECE WEIGHT ENHANCEMENT FUNCTION b. By Sampling method when the unit piece weight is not known In order to obtain the best counting result and to avoid and minimize sampling error, this scale is equipped with 5.5.a Procedures of Direct Entry Method AUTO UNIT PIECE WEIGHT ENHANCEMENT FUNCTION.
  • Page 9 Should increasing the sample size is not possible. AUTO UNIT PIECE WEIGHT ENHANCEMENT FUNCTION will be terminated when a zero weight is detected during the Counting operations may proceed but greater tolerance transaction process. on counting results has to be allowed. 5.7.
  • Page 10 NOTE 1 : If no unit piece weight is applied, only weight 5.9.4 To Clear Accumulated Data from Memory data will be saved to memory. a. Press MR b. Total accumulated data will be displayed on 3 display 5.9.2 Adding Quantity to Memory Manually panels Follow the below procedures to add quantity to memory c.
  • Page 11 c. Enter preset weight value through numeric keys a. By Direct entry method, or d. Value entered is shown on the UNIT WEIGHT PANEL b. By Current unit piece weight method e. Press @WT/SET to confirm f. Scales displays CH._Wt on the UNIT WEIGHT PANEL while 5.11.a Direct Entry Method the value entered on the WEIGHT PANEL...
  • Page 12 5.12.3 When Using DOS System 5.11.3 Clear Unit Piece Weight PLU a. Press 0 a. Create BASICA computer program file as below to b. Press and hold the preferred PLU location to clear enable the computer to receive data sent by scale. c.

  • Page 13: Troubleshooting

    6. TROUBLESHOOTING PSC = Total quantity. An underlined heading will be transmitted if M+ is pressed for the first time. SyndromeScale cannot be turned on NOTE 2: Check: Is the scale charged? By pressing M+ again, the data of 2 transaction is Action: Recharge the scale for at least 8 hours...

  • Page 14: Error Codes And Descriptions

    7. ERROR CODES AND DESCRIPTIONS Syndrome When turning on scale, all display PANEL blank out but only the ZERO and TARE INDICATOR appear Err_1: Accumulation error. Check Is any load applied to platter when turning M+ cannot be activated when weight applied is scale on? zero or while the same transaction has already Action:...

  • Page 15: Daily Care And Maintenance

    8. DAILY CARE AND MAINTENANCE a. Precision measuring device, handle with extreme care. b. Clean the scale with a soft and damp cloth. If necessary, apply a mild detergent. c. Do not use any harsh, abrasive material, acetone, volatile solvent, thinner or alcohol for cleaning. d.
Save PDF