Table of Contents
Advertisement
SEK SERIES
ELECTRONIC PIECE COUNTING / CHECK
WEIGHING SCALE
OPERATION MANUAL
READ THIS MANUAL BEFORE OPERATING THE SCALE
*Specifications and functions subject to change without prior notice
X0SEK030000 Revision: April 2008
CONTENT
1
2
3
4
5
6
7
8
Page: 1
2
3
4
5
7
8
14
15
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for UWE SEK-3000
Summary of Contents for UWE SEK-3000
-
Page 1: Table Of Contents
CONTENT CAUTION SPECIFICATIONS SEK SERIES FEATURES ELECTRONIC PIECE COUNTING / CHECK KEYBOARD LAYOUT & FUNCTIONS WEIGHING SCALE DISPLAY INDICATORS OPERATION MANUAL INTERNAL FUNCTIONS TROUBLESHOOTING CALIBRATION READ THIS MANUAL BEFORE OPERATING THE SCALE *Specifications and functions subject to change without prior notice X0SEK030000 Revision: April 2008 Page: 1... -
Page 2: Caution
Model No. Capacity (Max) Division (e) Check and make sure that the input voltage of power adaptor matches with the output voltage of the outlet. If it SEK-3000 3000g / 6.6lb 0.05g / 0.01oz SEK-6000 6000g / 13.2lb 0.1g / 0.01oz... -
Page 3: Features
FEATURES KEYBOARD LAYOUT & FUNCTIONS Manual Zero Fuction (± 2% F.S.) Tare Function (Full Tare Available) Selectable Resolution and Weighing Units ( Resolution: 1/60,000, 1/30,000 or 1/15,000) (Weighing Units: g, lb, lb-oz, tael, or pcs) Low Battery Warning Indicator ( ... - Page 4 KEYBOARD LAYOUT & FUNCTIONS KEYBOARD LAYOUT & FUNCTIONS 4- TARE When inputting HI-OK-LO value or a load is placed on the scale, Press this key to tare off the weight of the load on the platter (full press and hold MODE/RANGE to set the displayed value as the tare available).
-
Page 5: Display Indicators
KEYBOARD LAYOUT & FUNCTIONS DISPLAY INDICATORS 10- HIGH LIMIT 13- CHARGE STATUS LIGHT When inputting the number using the numeric keypad or This LED light displays the charging status. When charging placing a load on the scale, press this key to set the HI limit for using the adaptor, the LED will turn red. -
Page 6: Internal Functions
DISPLAY INDICATORS INTERNAL FUNCTIONS 19- LOW-BATTERY INDICATOR To access the internal functions: ***This sign appears when the battery is low. <1> Press and hold TARE, then press <ON/ZERO> <2> Display will show “F0” 20- M+ INDICATOR <3> Press TARE until the desired Function is displayed An arrow on this sign indicates the accumulation function is in <4>... - Page 7 INTERNAL FUNCTIONS INTERNAL FUNCTIONS Sound Alarm for HI-OK-LO (nobEEP, gobEEP, HLbEEP, (F4) Auto Power off Function HbEEP, LbEEP). a) Use the procedure described above to reach Function F4 F10 Relay Output Mode Selection (Act L – open / close, Act H b) Press MODE/RANGE.
- Page 8 INTERNAL FUNCTIONS INTERNAL FUNCTIONS c) After Baud rate is selected, press MODE/RANGE, and the a) Use the procedure described above to reach Function F6. display will show “P=XXX”. Select Parity Setting by b) Press MODE/RANGE and display will show “FiLt_X” (X pressing SAMPLE.
- Page 9 INTERNAL FUNCTIONS INTERNAL FUNCTIONS (F8) Tare Mode Selection d) Press TARE to confirm, then press ON/ZERO to return to a) Use the procedure described above to reach Function F8. normal weighing mode. b) Press MODE/RANGE to enter, and display will show “X-tArE”...
-
Page 10: Troubleshooting
TROUBLESHOOTING CALIBRATION Syndrome Possible Cause Solution Press ON/ZERO to turn on the scale. Before the countdown Scale cannot be Adaptor not Re-plug the finish from 9 to 0 press and hold MODE/RANGE key. turned on plugged correctly. adaptor to the The display will show “CAL.?_1”...
Need help?
Do you have a question about the SEK-3000 and is the answer not in the manual?
Questions and answers