HGM SERIES CONTENTS (UPGRADE VERSION) CAUTIONS ELECTRONIC WEIGHING SCALE 1. INSTALLATION OPERATION MANUAL 2. SPECIFICATIONS 3. KEYBOARD LAYOUT AND DESCRIPTION PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE 4. INITIAL SETUP ATTEMPT TO OPERATE THE SCALE 5. INSTRUCTION FOR USE 6. TROUBLE SHOOTING 7.
CAUTIONS 1. INSTALLATION 1. This unit is legal for trade only when it is sealed Check and make sure that the following accessories (and/or stamped) and bearing a serial number. Do not are included: attempt to break the seal (or stamp) affixed to this Operation Manual x 1 scale or remove the serial number.
2. SPECIFICATIONS 3. KEYBOARD LAYOUT AND DESCRIPTION Model No. Capacity Readability Accuracy (Max) HGM-2000 2kg/4.4lb 0.1g/0.0002lb 1/20000 HGM-4000 4kg/8.8lb 0.2g/0.0005lb 1/20000 HGM-10K 10kg/22lb 0.5g/0.001lb 1/20000 HGM-20K 20kg/44lb 1g/0.002lb 1/20000 Tare Range Full Tare Range Power-on ¡10% Max Zero Range Zero Range ¡2% Max Power Source By Built-in Rechargeable Battery or AD/DC Power Adaptor...
Page 4
METRIC UNIT INDICATOR 11. LO-BAT INDICATOR This indicator appears to indicate the weighing unit When this indicator appears, recharge the scale currently engaged is in metric unit (kg or g) immediately. Failure to do so may cause unrecoverable damage to the rechargeable battery inside scale AVOIRDUPOIS UNIT INDICATOR This indicator appears to indicate the weight unit currently engaged is in avoirdupois (pound)
4. INITIAL SETUP 4.2.2 Select Auto Power Off Setting The scale is equipped with Auto Power Off Function. The 4.1 PLACING THE SCALE scale will power off automatically if it is not used In order to obtain an accurate weighing result, the scale for 4 minutes.
Page 6
Press SAMPLE SET four times Press SAMPLE SET five times Scale displays F.5 Scale displays F.7 Press MODE to select baud rate of 4800, 9600 and Press MODE to select transmission mode ¡§trAn1¡¨ o 19200 ¡§trAn2 Press and hold MODE for 2 seconds to enter When the preferred data transmission mode shows on transmission protocol setup display, press ON/RE-ZERO to confirm and restart...
5. INSTRUCTION FOR USE Scale displays F.9 Press MODE to select between ¡Tr_on¡¨ or TroFF¡ -To enable Auto Tare Function, press SAMPLE SET when 5.1 BEFORE WEIGHING Make sure that: Tr_on appears -To disable Auto Tare Function, press SAMPLE SET The plastic platter is placed correctly on top of when TroFF appears load receptor and the stainless steel platter cover...
Page 8
5.3 SELECT WEIGHT UNIT 5.6 SET DISPLAYED VALUE TO ZERO WHEN UNLOADED Press MODE to shift between metric or avoirdupois weight By pressing ON/RE-ZERO, a positive or negative weight units. The weight unit used before power off would be displayed will be set to zero and ZERO INDICATOR appears. employed when the scale is turned on again.
Page 9
The tare effect will be cancelled: NOTE: -Automatically if automatic tare function is If no weight is placed on the platter during sampling, employed, or scale will return to normal operation after 6 seconds When corresponding quantity is placed on the -By pressing ON/RE-ZERO After ON/RE-ZERO is pressed, the TARE INDICATOR platter, press SAMPLE SET to execute the average...
6. TROUBLE SHOOTING NOTE: The charging indicator is located on the left side of scale and it will only light up when charging. Syndrome Scale cannot be turned on Red color: Recharging battery Check: Is the scale charged? Green color: Charging completed Action: Recharge the scale for at least 8 hours before first time use or plug in the power...
7. DAILY CARE AND MAINTENANCE Check Is there anything obstructing the platter? Action Remove all obstacles. Clean the scale with a soft and damp cloth. If necessary, apply a mild detergent. Syndrome Weighing result is not accurate Check Is the scale placed in a level condition? Do not use any harsh, abrasive material, acetone, Action Adjust the adjustable feet to a level...
Need help?
Do you have a question about the HGM Series and is the answer not in the manual?
Questions and answers