Subscribe to Our Youtube Channel
Related Manuals for UWE DM-3000
Summary of Contents for UWE DM-3000
-
Page 1: Table Of Contents
DM SERIES CONTENTS CAUTIONS ELECTRONIC WEIGHING SCALE 1. INSTALLATION 2. SPECIFICATIONS OPERATION MANUAL 3. KEYBOARD LAYOUT AND DESCRIPTION 4. INITIAL SETUP PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 5. INSTRUCTION FOR USE 6. TROUBLE SHOOTING 7. - Page 2 CAUTIONS Do not use this scale for chemical substances or in any environment that contains chemical 1. This unit is legal for trade only when it vapor. is sealed (and/or stamped) and bearing a serial number. Do not attempt to break the 6.
-
Page 3: Installation
1. INSTALLATION 1.1 Check and make sure that the following accessories are included: This operation manual Scale x 1 Plastic platter x 1 Stainless steel cover x 1 Power adaptor x 1 Contact your dealer if any item missed. FIG 2 1.2 Locks the plastic platter (FIG 1 A) to the platter holder, with the screw (FIG 1 B) included, and then apply the rubber cap... -
Page 4: Specifications
2. SPECIFICATIONS 1.4 Power on the scale a. Before plugging the power adaptor into Model No. Capacity Division Accuracy Min.Load electricity outlet, check and make sure DM-3000 3000g 1/3000 that the input voltage of power adaptor DM-6000 6000g 1/3000 matches with the output voltage of the... -
Page 5: Keyboard Layout And Description
3. KEYBOARD LAYOUT AND DESCRIPTION 4. OFF KEY Press this key to turn scale off. 5. ZERO INDICATOR This indicator appears to indicate a zero weight status. 6. TARE INDICATOR This indicator appears to indicate the tare function operation weight displayed is net weight. -
Page 6: Initial Setup
4. INITIAL SETUP 10. WEIGHT UNIT INDICATOR This indicator appears to indicate the weighing unit being selected. 4.1 PLACING THE SCALE avoirdupois weight units are available and In order to obtain an accurate weighing result, this indicator means the weighing unit is the scale must be placed on a strong and level at decimal pound (e.g. - Page 7 e. Press and hold MODE for 3 second and then e. Scale displays F.4 release. f. Press MODE to shift between 0._OFF and f. Press MODE to shift between desired 4._OFF. configurations appears. g. To enable Auto Power Off Function, press g.
-
Page 8: Instruction For Use
5. INSTRUCTION FOR USE g. Press ON/ZERO to confirm and return to normal operation. 5.1 BEFORE WEIGHING Note: Make sure that: No transmission will be activated if weight a. The plastic platter is screwed firmly and detected is less than 20e. the stainless steel platter cover is placed on the plastic platter. - Page 9 5.3 SELECT WEIGHT UNIT 5.6 TARE OFF THE WEIGHT OF A CONTAINER Press MODE to shift among kg à decimal lb à When a container is used, follow the below steps lb/oz. à kg weight units. Refer to 4.2.1 for to tare off the weight of the container and internal setting procedures.
-
Page 10: Trouble Shooting
6. TROUBLE SHOOTING 5.8 RECHARGE THE SCALE scale equipped with built-in rechargeable battery. When LO-BAT Syndrome Scale cannot be turned on INDICATOR appears, recharge scale Check: Is the scale charged? immediately. Failure to do so may cause Action: Recharge the scale for at least 8 unrecoverable damage to the rechargeable hours before first time use or plug battery. - Page 11 00000 Syndrome Rated capacity cannot be reached Syndrome Scale displays Check Is the TARE INDICATOR on? Check Is the scale overloaded? Action: Turn the scale off. Remove all loads Action Remove some loads from platter. from platter and turn on again. Check Is there anything obstructing the Syndrome...
-
Page 12: Daily Care And Maintenance
7. DAILY CARE AND MAINTENANCE Clean the scale with a soft and damp cloth. If necessary, apply a mild detergent. Do not use any harsh, abrasive material, acetone, volatile solvent, thinner or alcohol for cleaning. Verify accuracy scale periodically. Re-calibrate the scale if necessary.
Need help?
Do you have a question about the DM-3000 and is the answer not in the manual?
Questions and answers