Subscribe to Our Youtube Channel
Related Manuals for UWE DW-3000E
Summary of Contents for UWE DW-3000E
-
Page 1: Table Of Contents
DW SERIES-LED CONTENTS (UPGRADE VERSION) CAUTIONS WASH DOWN ELECTRONIC WEIGHING SCALE 1. INSTALLATION 2. SPECIFICATIONS OPERATION MANUAL 3. KEYBOARD LAYOUT AND DESCRIPTION 4. INITIAL SETUP PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 5. INSTRUCTION FOR USE 6. - Page 2 CAUTIONS 8. Always apply the battery cap when not in charging. 1. This unit is legal for trade only when it is sealed 9. Check desiccant underneath the scale periodically. (and/or stamped) and bearing a serial number. Do not Should any part of the desiccant turns to pink attempt to break the seal (or stamp) affixed to this color, contact your dealer for scale inspection.
-
Page 3: Installation
1. INSTALLATION Check and make sure that the following accessories are included: This operation manual Scale x 1 Plastic platter x 1 Stainless steel cover x 1 Screw x 1 Rubber cap x 1 Power adaptor x 1 FIG 2 Contact your dealer if any item is missing. -
Page 4: Specifications
8 hours to ensure the best performance. (Max) Default High c. After battery is fully charged, remove adaptor Resolution DW-3000E 3000g 0.5g from scale. Apply the battery cap (FIG 2 E) to DW-6000E 6000g seal the DC input jack of scale. -
Page 5: Keyboard Layout And Description
3. KEYBOARD LAYOUT AND DESCRIPTION 5. IN-CHARGE INDICATOR Red color: Recharging battery Green color: Charging completed 6. ZERO INDICATOR This indicator appears to indicate a zero weight status 7. TARE INDICATOR This indicator appears to indicate the tare function is in operation and weight displayed is net weight 1. -
Page 6: Initial Setup
4. INITIAL SETUP 11. OK INDICATOR This indicator appears to indicate the weight detected within the high and low limit range (Weight check 4.1 PLACING THE SCALE function) In order to obtain an accurate weighing result, the scale must be placed on a strong and level surface. 12. - Page 7 4.2.2 Select Auto Power Off Setting Press TARE four times The scale is equipped with Auto Power Off Function. The Scale displays F.5 scale will power off automatically if it is not used Press MODE to select baud rate of 4800, 9600, 19200, for 4 minutes.
- Page 8 Press TARE five times Scale displays F.9 Scale displays F.7 Press MODE to select between Tr._on or Tr.oFF Press MODE to select transmission mode of trAn1 or -To enable Auto Tare Function, press TARE when Tr._on trAn2 appears When the preferred data transmission mode shows on -To disable Auto Tare Function, press TARE when display, press ON/ZERO to confirm and restart the Tr.oFF appears...
-
Page 9: Instruction For Use
5. INSTRUCTION FOR USE 5.3 SELECT WEIGHT UNIT Press MODE to shift between metric or avoirdupois weight 5.1 BEFORE WEIGHING units. The weight unit used before power off would be Make sure that: employed when the scale is turned on again. The plastic platter is screwed firmly and the stainless steel platter cover is placed on the NOTE:... - Page 10 Remove all loads from platter Turn scale on Refer to 5.2 for weighing procedures. Weight displayed Scale displays zero weight; if not, press ON/ZERO under is the net weight of the subject matter. Refer Press and hold ON/ZERO. Scale displays: to SPECIFICATIONS for maximum tare range.
- Page 11 Press and hold ON/ZERO, then press TARE -bb_H. = buzzer warning when weight detected above The HI INDICATOR appears and the cursor is flashing, the high weight limit set. scale is now in upper weight limit setup When the require buzzer warning setting is selected, Utilize MODE, TARE and ON/ZERO to set the required press and hold ON/ZERO, then press TARE to return high weight limit...
-
Page 12: Trouble Shooting
6. TROUBLE SHOOTING over the high weight limit preset The OK INDICATOR will appear when weight detected within the high upper and low weight limit Syndrome Scale cannot be turned on The LO INDICATOR will appear when weight detected Check: Is the scale charged? under the low weight limit preset Action:... -
Page 13: Daily Care And Maintenance
7. DAILY CARE AND MAINTENANCE Check Is there anything obstructing the platter? Action Remove all obstacles. Clean the scale with a soft and damp cloth. If necessary, apply a mild detergent. Syndrome Weighing result is not accurate Check Is the scale placed in a level condition? Do not use any harsh, abrasive material, Action Adjust the adjustable feet to a level...
Need help?
Do you have a question about the DW-3000E and is the answer not in the manual?
Questions and answers