Zephyr Cache CCA-E30ASX Use, Care & Installation Manual
Hide thumbs
Also See for Cache CCA-E30ASX:
- Use, care and installation manual (22 pages) ,
- Use, care and installation manual (23 pages)
Related Manuals for Zephyr Cache CCA-E30ASX
Summary of Contents for Zephyr Cache CCA-E30ASX
- Page 1 CACHE CCA-E30ASX CCA-E36ASX CCA-E48ASX Model number: Serial Number: Date of Purchase: Sales Dealer: DEC06.0101 © Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
-
Page 3: Table Of Contents
SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ......................Preparing the Electrical Wires ....... Internal Blower (Vertical Ducting) 10-11 ......Internal Blower (Horizontal Ducting) 12-13 ....External Blower Prepartion ........ -
Page 4: Safety Notice
www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. - Page 5 CAUTION maximum 6.2 amps, 120V AC 60Hz or internal blowers manufactured by Zephyr Ventilation, models CBI-600A. WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION crawl spaces or garages. WARNING TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL CONTROL/ SWITCH.
-
Page 6: List Of Materials
www.zephyronline.com MODEL: CCA-E30ASX, CCA-E36ASX, CCA-E48ASX 1 - Hood Cache Hardware M4 * 8 x 22 wire cap x 3 M4 * 6 M3.5 * 10 CBI-600A Hardware M4 * 10 M4 * 16... -
Page 7: Ducting Calculation Sheet
Equivalent number Equivalent number Duct pieces Duct pieces length x used Total length x used Total 3-1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8” Round, 30 Ft. -
Page 8: Mounting Height & Clearance
www.zephyronline.com Minimum mount height between range top and Maximum mount height should be no higher than It is important to install the hood at the proper mounting height. Hoods mounted too low could mounted too high will be hard to reach and will 10-23/64"... -
Page 9: Ducting Options
WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Some Ducting Options External Blower External Blower Soffit or crawl space Roof Pitch w/ Flashing &... - Page 10 www.zephyronline.com 29-61/64” - (30“), 35-61/64” - (36“), 47-29/32” - (48”) 4-3/16” 1-1/8” 9-29/32” 27-7/8” - (30“), 33-7/8” - (36“), 45-53/64 - (48”) 2-3/4” 3-19/32” 12” 2” 4-3/16” 5-5/32” 22-1/8” ext. blower AC power knock-out knock-out...
-
Page 11: Preparing The Electrical Wires
ELECTRICAL WARNING how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electrical Supply: This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. -
Page 12: Internal Blower (Vertical Ducting)
www.zephyronline.com INTERNAL BLOWER PREPARATION – VERTICAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4*10 screws included with internal blower. 3. Connect 6 pin male connector from capacitor box to 6 pin female connector on control board box. - Page 13 7. Connect 9 pin male connector from blower to 9 pin female connector on capacitor box.
-
Page 14: Internal Blower (Horizontal Ducting)
www.zephyronline.com INTERNAL BLOWER PREPARATION – HORIZONTAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4*10 screws included with internal blower. 4. Place solid mounting plate on top of hood and 3. - Page 15 7. Place blower over round to rectangular adapter 8. Install blower with round to rectangular adapter as shown above. into hood. 9. Mount blower brackets to hood using two 10. Install rectangular starting collar to back of hood using six M4*8 screws recently removed from are included with internal blower.
-
Page 16: External Blower Prepartion
www.zephyronline.com EXTERNAL BLOWER PREPARATION 2. Install threaded cable lock and external blower wiring through the knockout next to and secure using eight M4*8 screws. the electrical wiring knockout. 3. Place cap over threaded cable lock and secure 4. Connect 6 pin male connector from external blower wiring to 6 pin female connector on by turning cap clockwise. -
Page 17: Mounting The Range Hood
1. Select preferred duct location (internal blower - vertical or horizontal, external blower - vertical only). 5. Duct opening additional strengthening is required. Must be cutout placed inside frameless cabinets. 4. Temporarily position the range hood in the desired mounting location. Measure and duct/silver tape mark the mounting holes, duct and electrical... -
Page 18: Touch Controls
www.zephyronline.com Lights On/Off/Dim Display (Speed level, Delay Off Indicator) 5 Min Delay Off Blower On/Off Adjust 3 Speed Levels Blower On/Off By pressing , the blower is switched On and Off. When switched on, the blower starts up on the same speed it was turned off at. When switched off the entire hood powers off, including the lights. Speed Selection The 3 speed levels are selected by pressing to decrease and... -
Page 19: Cleaning And Installing Filters
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scoring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless depending on cooking habits. - Page 20 www.zephyronline.com REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
-
Page 21: Troubleshooting
TROUBLESHOOTING PROCEDURES FOR CACHE Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2. - Page 22 Have your product proof of purchase with date ready for warranty issues. Or write to: Zephyr Corporation Service and Warranty Department 395 Mendell Street...
Need help?
Do you have a question about the Cache CCA-E30ASX and is the answer not in the manual?
Questions and answers