Zephyr CCA-E30ASX Use, Care And Installation Manual
Hide thumbs
Also See for CCA-E30ASX:
- Use, care and installation manual (22 pages) ,
- Use, care & installation manual (22 pages)
Related Manuals for Zephyr CCA-E30ASX
Summary of Contents for Zephyr CCA-E30ASX
- Page 1 CACHE CCA-E30ASX CCA-E36ASX CCA-E48ASX Model number: Serial Number: Date of Purchase: Sales Dealer: NOV12.0301 © Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
-
Page 3: Table Of Contents
SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifi cations ........... Preparing the Electrical Wires ....... Internal Blower (Vertical Ducting) 10-11 ......Internal Blower (Horizontal Ducting) 12-13 .... -
Page 4: Safety Notice
www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. - Page 5 CAUTION To reduce the risk of fi re and electric shock, install this range hood only with external blower models CBE-1000, rated maximum 6.2 amps, 120V AC 60Hz or internal blowers manufactured by Zephyr Ventilation, models CBI-600A. WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
-
Page 6: List Of Materials
MODEL: CCA-E30ASX, CCA-E36ASX, CCA-E48ASX 1 - Hood 2 - Baffl e fi lters (3) for 48” model 2 - Halogen light bulbs (4) for 48” model 1 - 6” round top mounting plate 1 - Solid top mounting plate... -
Page 7: Ducting Calculation Sheet
Equivalent number Equivalent number Duct pieces Duct pieces length x used Total length x used Total 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8” Round, 30 Ft. -
Page 8: Installation
www.zephyronline.com Minimum mount height between range top and hood bottom should be no less than 24”. Maximum mount height should be no higher than 32”. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fi... -
Page 9: Ducting Options
WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options External Blower... -
Page 10: Hood Specifi Cations
www.zephyronline.com Back View Front View 29-61/64” - (30“), 35-61/64” - (36“), 47-29/32” - (48”) 4-3/16” 1-1/8” 9-29/32” Side View Top View 27-7/8” - (30“), 33-7/8” - (36“), 45-53/64 - (48”) 2-3/4” 3-19/32” 12” 2” 4-3/16” 5-5/32” 22-1/8” ext. blower AC power knock-out knock-out... -
Page 11: Preparing The Electrical Wires
ELECTRICAL WARNING All Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. -
Page 12: Internal Blower (Vertical Ducting)
www.zephyronline.com INTERNAL BLOWER PREPARATION – VERTICAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4*10 screws included with internal blower. 3. Connect 6 pin male connector from capacitor box 4. - Page 13 7. Connect 9 pin male connector from blower to 9 pin female connector on capacitor box.
-
Page 14: Internal Blower (Horizontal Ducting)
www.zephyronline.com INTERNAL BLOWER PREPARATION – HORIZONTAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4*10 screws included with internal blower. 4. Place solid mounting plate on top of hood and 3. - Page 15 7. Place blower over round to rectangular adapter 8. Install blower with round to rectangular adapter as shown above. into hood. 9. Mount blower brackets to hood using two 10. Install rectangular starting collar to back of hood 3/16” * 3/8” screws for each bracket. Screws using six M4*8 screws recently removed from are included with internal blower.
-
Page 16: External Blower Prepartion
www.zephyronline.com EXTERNAL BLOWER PREPARATION 2. Install threaded cable lock and external 1. Place 8” round mounting plate on top of hood blower wiring through the knockout next to and secure using eight M4*8 screws. the electrical wiring knockout. 4. Connect 6 pin male connector from external 3. -
Page 17: Mounting The Range Hood
Hood is designed for installation under a kitchen cabinet 1. Select preferred duct location (internal blower - vertical or horizontal, external blower - vertical only). 5. Duct opening 2. Begin installation by removing the baffl e fi lters. cutout 3. Reinforce cabinet with 1” x 2” wood strips if additional strengthening is required. -
Page 18: Touch Controls
www.zephyronline.com Lights On/Off/Dim Display (Speed level, Delay Off Indicator) 5 Min Delay Off Blower On/Off Adjust 3 Speed Levels Blower On/Off By pressing , the blower is switched On and Off. When switched on, the blower starts up on the same speed it was turned off at. When switched off the entire hood powers off, including the lights. Speed Selection The 3 speed levels are selected by pressing to decrease and... -
Page 19: Features
Baffle Filter Clean Reminder Whether your hood is installed as an exhaust or purifying unit, a set if baffle filters are fitted by the factory, These baffle filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean. -
Page 20: Cleaning And Installing Filters
www.zephyronline.com SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scoring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless luster and grain. - Page 21 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
-
Page 22: Troubleshooting
www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR CACHE Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2. - Page 23 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows: Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.