Zephyr CACHE CCA-E36ASX Use, Care And Installation Manual
Cheng collection
Hide thumbs
Also See for CACHE CCA-E36ASX:
- Use, care and installation manual (23 pages) ,
- Use, care & installation manual (22 pages)
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Zephyr CACHE CCA-E36ASX
Summary of Contents for Zephyr CACHE CCA-E36ASX
- Page 1 ZEPh'_ CNENG COLLECTION www.zephyronline.com CACHE CCA-E30ASX ii mmllm CCA-E36ASX CCA-E48ASX ii mmllm "O Model number: Serial Number: Date of Purchase: Sales Dealer: DEC06.0101 {9 Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
-
Page 3: Table Of Contents
SAFETY NOTICE ..........LIST OF MATERIALS ......... INSTALLATION Ducting Calculation Sheet ......Mounting Height & Clearance ......Ducting Options ..........Hood Specifications ........Preparing the Electrical Wires ....... Internal Blower (Vertical Ducting) ....10-11 Internal Blower (Horizontal Ducting)_.._.._..___. 12-13 External Blower Prepartion ......Mounting the Range Hood ........ -
Page 4: Safety Notice
READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. - Page 5 To reduce the risk of fire and electric shock, install this range hood only with external blower models CBE-1000, rated maximum 6.2 amps, 120V AC 60Hz or internal blowers manufactured by Zephyr Ventilation, models CBI-600A. WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
-
Page 6: List Of Materials
MODEL: CCA-E30ASX, CCA-E36ASX, CCA-E48ASX 1 - Hood 2 - Baffle Filters (3) for 48" model 2 - Halogen Lights (4) for 48" model 1 - 6" round top mounting plate 1 - Solid top mounting plate 1 - Rectangular starting collar 1 - Round to rectangular adapter 2 - Blower brackets 1 - 8"... -
Page 7: Ducting Calculation Sheet
Duct pieces i Equivalent number Duct pieces Equivalent number length x used Total length x used Total ............... }.......... 3-1/4"x10" 1Ft. 6'L8"Round 30Ft, :_straight with damper Rect., wall cap dl,,,l 3 1/4" x 10" i rect, transition 3-t/4" x 10" i T' round to 15Ft. - Page 8 Minimum mount height between range top and hood bottom should be no less than 24". Maximum mount height should be no higher than 32". It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard;...
-
Page 9: Cleaning And Installing Filters
WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape. Some Ducting Options External Blower... -
Page 10: Hood Specifications
29-61/64"- (30"), 35-61/64"- (36"), 47-29/32" - (48") 4-3/16" 1-1/8" ° °9-29/32 ,:° 27-7/8"- (30"), 33-7/8"- (36"), 45-53/64- (48") 2-3/4" _-2" :_/_,, 4-3/1 ext. blower AC power knock-out knock-out... -
Page 11: Preparing The Electrical Wires
ELECTRICAL WARNING All Electrical work must by performed by qualified electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. -
Page 12: Internal Blower (Vertical Ducting)
INTERNAL BLOWER PREPARATION - VERTICAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4"10 screws included with internal blower. 3. Connect 6 pin male connector from capacitor box 4. - Page 13 7_M_ 7. Connect 9 pin male connector from blower to 9 pin female connector on capacitor box.
-
Page 14: Internal Blower (Horizontal Ducting)
INTERNAL BLOWER PREPARATION - HORIZONTAL DUCTING 2. Attach green ground wire to ground screw on 1. Attach capacitor box to inside of hood using two hood. M4"10 screws included with internal blower. Place solid mounting plate on top of hood and secure using eight M4"8 screws. - Page 15 7. Place blower over r ound t orectangular adapter 8. Install blower withround t orectangular adapter asshown a bove. intohood. Mount blower brackets tohood using two 10.Install rectangular starting c ollar t oback ofhood 3/16" * 3/8" screws foreach bracket. Screws using sixM4"8 screws r ecently removed from areincluded withinternal blower.
-
Page 16: External Blower Prepartion
EXTERNAL BLOWER PREPARATION Install threaded cable lock and external 1. Place 8" round mounting plate on top of hood blower wiring through the knockout next to and secure using eight M4"8 screws. the electrical wiring knockout. Connect 6 pin male connector from external Place cap over threaded cable lock and secure... -
Page 17: Mounting The Range Hood
1. Select preferred duct l ocation ( internal blower - vertical orhorizontal, external blower -vertical only). 2. Begin i nstallation byremoving thebaffle filters. 5. Duct 3. Reinforce cabinet with1"x2"wood strips if opening additional strengthening isrequired. Must b e cutout placed i nside f rameless cabinets. 4. -
Page 18: Touch Controls
O Lights On/Off/Dim (Speed Jevel, Delay Qff Indicator) DisllaY 5 Min Delay Off Blower On/Off Adjust 3 Speed Levels Blower On/Off By pressing (_), the Mower is switched On and Off. When switched on, the Mower starts up on the same speed it was turned off at. When switched off the entire hood powers off, including the lights. Speed Selection The 3 speed levels are seEected by pressing _--_to decrease and (_ to increase speed level The... - Page 19 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scoring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain.
- Page 20 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
-
Page 21: Troubleshooting
TROUBLESHOOTING PROCEDURES FOR CACHE Cause Issue What to do 1. Make sure the circuit breaker and the unit's After installation, 1. The power source is not turned ON. the unit doesn't power is ON. work. 2. The power line and the cable locking connector 2. - Page 22 When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr's Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses. Services outside of service area and the labor cost incurred in connection with the removal, shipping and reinstallation cost, nor does it cover any other contingent expenses.
Need help?
Do you have a question about the CACHE CCA-E36ASX and is the answer not in the manual?
Questions and answers