Related Manuals for Zephyr Napoli Island ZNA-E42S
Summary of Contents for Zephyr Napoli Island ZNA-E42S
- Page 1 Napoli Island ZNA-M90S ZNA-E42S Model number: Serial Number: MAR09.0102 © Zephyr Corporation...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Hood Specifi cations Mounting the Hood Ductless Recirculation CONTROLS MAINTENANCE Hood and Filter Cleaning Lights TROUBLESHOOTING LIST OF PARTS AND ACCESSORIES 9 - 10 12-14...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 Electrical Diagram on product. A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary. ZNA-M90S - 500 Watts, 4.1 Amps ZNA-E42S - 500 Watts, 4.1 Amps...
- Page 6 MODELS: ZNA-M90S, ZNA-E42S PARTS SUPPLIED 1 - Top duct cover 1 - Bottom duct cover 1 - 6” round damper, pre-installed 1 - Hood body 4 - 50W GU-10 halogen lights 3 - Metal mesh filters HARDWARE PACKAGE CONTENTS (3) Wire Nuts (4) M4 x 1-1/2”...
- Page 7 Equivalent number Duct pieces length x used 3- 1/ 4” x 10” 1 Ft. Rect., straight 7” Round, 1 Ft. straight 8” Round, 1 Ft. straight 3- 1/ 4” x 10” 15 Ft. Rect. 90 elbow 3- 1/ 4” x 10” 9 Ft.
- Page 8 Min. ducted 33” Min. recirc. 33” Max. 48” Min 28"-Max 36" Min 8’ 1" Max 10’ 36" DUCTING A minimum of 6” round ducting must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl...
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certifi...
- Page 10 front of hood 16 " 300 16 " /42"[1065] (blower housing and ceiling bracket) www.zephyronline.com top of hood 16 " 258 16 " 208 8 " 28 side of hood 16 " 218 16 " 650...
- Page 11 Add Blockings Fasten upper duct cover Install Duct Cover Adjust height & fasten frame CAUTION: At least two installers are required due to the weight and size of the hood. Fasten Support Frame 1. Add and secure blocking (minimum 2x4 studs onto ceiling joists.
- Page 12 Mount hood onto support frame 6. Lift lower duct cover and hood body onto bottom of support frame. 7. Secure hood body to bottom support with (4) screws. Access the screws from inside the hood. This will require at least two people. WARNING: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards.
- Page 13 Part No. Filters in Pkg. ZNA-M90S ZRC-0060 ZNA-E42S ZRC-0060 1. Purchase recirculating kit per the part number above. 2. Secure air diverter plate to top support frame. (FIG. F) Open sides of air diverter plate should face left and right and align with louver holes on the duct covers.
- Page 14 Blower On/Off 1. Blower On/Off By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 3. 2. Speed Selection The 6 speed levels are selected by pressing selected. 3. Delay Off This feature is used for programmed shut down of blower 15 minutes after the function is activated.
- Page 15 Charcoal Filter Change Reminder (charcoal filter, if installed) When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to be replaced after every 120 hours of use.
- Page 16 Metal Filter Clean Reminder (metal mesh filter) Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the factory, These metal mesh filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean.
- Page 17 Should fi lters wear out due to age and prolonged use, replace with following part number: Hood Model: Part No. Qty. to Order. ZNA-M90S 50200004 ZNA-E42S 50200004 Replace any damaged fi lter that has punctured or broken mesh or damaged frame.
- Page 18 Replacement bulbs are available at specialty lighting stores. Purchase type GU-10 50W halogen. Note: GU-10 halogen light bulbs apply to ZNA hoods ending in serial number xxxxxxxBxx only. For Zephyr part numbers please turn to page 18 of the manual.
- Page 19 TROUBLESHOOTING PROCEDURES FOR NAPOLI ISLAND Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 20 DESCRIPTION Replacement Parts Light Bulb GU10 50W (each) Metal Filter (each) Optional Accessories Recirculating Kit Replacement Charcoal Filter (each) Duct Cover Extension To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 www.zephyronline.com PART# Z0B-0020 50200004 ZRC-0060 Z0F-C002 Z1C-00NA...
- Page 21 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows: Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.